Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Assembly Expert

Blinky Lights II: The Hard Way
 
Take the last two digits of your UTCID. This is your duty cycle in percent. If your duty cycle is less than 10%, add 30 to your number.
 
Create an assembly program that runs on the MSP430 that will blink as LED at a rate of exactly 1 Hz by using the duty cycle you found from your UTCID. 
 
For illustration: if your UTCID was ABC123, your duty cycle would be 23%. Your LED should then be ON for 0.23 seconds and OFF for 0.77 seconds, so that the combined cycle time is exactly 1.00 seconds.
 
Deliverables:

•  A flowchart of your program.

•  Commented source code, see below.

•  Analysis proving that your code blinks the LEDs at the specified rates. This must involve a calculation including instruction cycle counts and your board’s clock frequency.

Comments:

• Comment your code at a level of detail enough for someone to follow it. More detail than that is not helpful.

• Include several comments lines at the very top of your program that describes the program, what it does, who wrote it, when it was written, what hardware it requires, and what inputs/outputs it uses. This is called a header. See below for an illustration.
 
; ex program for demonstrating header section, does nothing
; Targets MSP430G2231 on LaunchPad board
; Stephen Craven, ENEE 4700, 9/23/2010
; Program does what?
; Input is ... Output is... BE SPECIFIC. Include enough info for
; someone to configure and use your program.

Assembly, Programming

  • Category:- Assembly
  • Reference No.:- M91345

Have any Question? 


Related Questions in Assembly

Assembly languagelab assignmentin this lab we will write an

Assembly Language Lab Assignment In this lab we will write an assembly program to implement a Finite State Machine (FSM) that recognizes hexadecimal integer constant that conforms to MASM syntax. The hexadecimal constant ...

Assembly language labfibonacci numbers are integers 0 1 1 2

Assembly Language Lab Fibonacci numbers are integers 0, 1, 1, 2, 3, 5, 8, 13, 21 ... If function fib(n) represents the nth Fibonacci number, we have fib(n) = fib(n-1) + fib(n-2) for n > 2, and fib(1) = 0, fib(2) = 1. The ...

Binary is a numer system used by computers it consists of

Binary is a numer system used by computers. It consists of only two digits, 0 and 1, which represent off and on. In decimal numbers, there are ten digits, 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9. When you write 247 in decimal, ...

Problemyou have to write a subroutine assembly language

Problem: You have to write a subroutine (assembly language code using NASM) for the following equation. DX= (AX 2 + (AX-1) + 2*(AX+2))/2 Note: You cannot use MUL or DIV instructions, you have to perform multiplication an ...

Questions statementyou have to write a subroutine assembly

Questions Statement You have to write a subroutine (assembly language code using NASM) for the following equation. DX= (AX 2 + (AX-1) + 2*(AX+2))/2 Note: You cannot use MUL or DIV instructions, you have to perform multip ...

Project marie start code at bottom of Project MARIE Start code at bottom of document 1.

Project MARIE Start code at bottom of document 1. Introduction The objective of this project is to reinforce your understanding of computer organization, instruction set architectures, and assembly language. You will acc ...

Questions statementyou have to write a subroutine assembly

Questions Statement You have to write a subroutine (assembly language code using NASM) for the following equation. DX= (AX 2 + (AX-1) + 2*(AX+2))/2 Note: You cannot use MUL or DIV instructions, you have to perform multip ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro