+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

Q1. Illustrate the general beam bending equation and state what each symbol in the equation symbolizes and as well the empirical units of measurement for each term.

Q2. Illustrate the physical significance of I and E in the general bending equation?

Q3. Illustrate the standard formulae for computing I for a circular and rectangular cross sectional area.

Q4. Sketch a diagram pointing out how stress varies via a rectangular beam that is subjected to the bending.

Q5. Compute the second moment of area for:

a) A solid rectangular part 170 mm x 250 mm.

b) A solid circular part with radius of 100 mm.

c) A hollow rectangular part 90 mm x 150 mm with wall thickness of 10mm.

d) A hollow circular part of radius 50 mm and a wall thickness of 5mm.

e) A rectangular section 85 mm x 100 mm with a circular cut out with diameter 40mm.

Q6. A water channel employed to irrigate fields has to cross a small ravine. The channel is supported on three round logs, 150 mm in diameter, spanning a 5 m gap. The logs can be considered to be only supported and the trough, whenever full, can be considered as a distributed load of 0.8KN/m. Compute the maximum bending stress in one log and show where it takes place.

Q7. Cantilever style balcony is supported by two I beams, 2 m in length. The weight of balcony is uniformly supported by two beams and can be supposed to produce an evenly distributed load on each beam of 3 KN/m.

a) Compute the total weight of the balcony.

b) The nominal size of each beam is 114 mm x 114 mm with a thickness of 10 mm. Compute the maximum bending moment for one beam and state where it takes place.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M99747

Have any Question?

## Related Questions in Mechanical Engineering

### One excited state of the sodium atom lies at 25 73986 cm1

One excited state of the sodium atom lies at 25 739.86 cm1 above the ground state, another lies at 50 266.88 cm-1 . Suppose they are connected by a perturbation equivalent in energy to (a) 100 cm -1 , (b) 1000 cm -1 , (c ...

### An electronic scoreboard is to be installed in a large

An electronic scoreboard is to be installed in a large stadium. Due to the design of the roof structure, the suspending cables will have different lengths, as is shown below. a. Determine a suitable cross-sectional area ...

### Determme the dimensions in both the flt system anltlthe mlt

Determme the dimensions, in both the FLT system an (a) the product of force times acceleration, (b) the product of force times velocity divided by area. and (c) momentum divided by volume

### 1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

### Bull why do individual bolts relax a bit when first

• Why do individual bolts relax a bit when first tightened? Name several factors that can increase the relaxation ? Which will tend to loose more preload after initial tightening, a short bolt or a long bolt? • What are ...

### 1 gas turbine and compressed air systems will serve as

1. Gas turbine and compressed air systems will serve as prime movers at a very high speed. Discuss the design characteristics of an induction generator for those applications. 2. Explain in detail why induction generator ...

### A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

### Many devices have been developed to measure the viscosity

Many devices have been developed to measure the viscosity of fluids. One such device, known as a rotational viscometer, involves a pair of concentric cylinders with radii r i and r o , and total length L. The inner cylin ...

### It has been observed that the most effective way to crush

It has been observed that the most effective way to crush an empty aluminum beverage can is to apply an eccentric compressive load. Use buckling theory to explain this phenomenon. The can wall thickness is 80 μm, and the ...

### Select a topic on the discussion board discussion section

Select a topic on the discussion board (DISCUSSION section of blackboard) There are four categories of topics; organizations, testing methods, elements and specialty components. Each has something to do with industrial m ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen