Ask Mechanical Engineering Expert

HEAT TRANSFER AND COMBUSTION

You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA.

1. A fuel gas consists of 75% butane (C4H10), 10% propane (C3H8) and 15% butene (C4H8) by volume.

It is to be fed to the combustion chamber in 10% excess air at 25ºC, where it is completely burnt to carbon dioxide and water. The flue gases produced are to be used to generate 5 bar steam from water at 90ºC.

With the aid of the data at the end of the question, steam tables and the enthalpy table given in the Appendix of lesson HTC - 4 - 2:

(a) Write balanced equations for the combustion of each component of the fuel gas.

(b) Explain the need for excess air.

(c) Determine the actual fuel:air ratio

(i) by volume
(ii) by mass.

(d) Calculate:

(i) the net calorific value (CV) per m3 of the fuel/air mix at 25ºC
(ii) the net calorific value (CV) per kmol of the fuel/air mix at 25ºC.

(e) Determine the composition of the flue gases by volume (assuming the inlet air is dry):
(i) on a wet basis
(ii) on a dry basis.

(f) Determine the maximum flame temperature.

(g) State how varying the amount of excess air may affect the flame temperature.

(h) Determine the ‘furnace efficiency' if the flue gases leave the boiler at 300ºC.

(i) If 5% of the heat available for steam production is lost to the atmosphere, determine the amount of steam raised per hour when the total flow of flue gases is 1400 kmol h-1.

(j) Determine the dew point temperature assuming that the flue gas pressure is 1.00 bar and the inlet air:
(i) is dry
(ii) contains 0.8 kg water per kmol of air at the temperature of the inlet air.

(k) If the flue gases exiting the boiler are used to preheat the water fed to the boiler from a temperature of 28ºC to 90ºC and assuming:
- a mean specific heat capacity for water over this temperature range to be 4.2 kJ kg-1 K-1
- a mean molar heat capacity for the flue gases up to 300ºC to be 31 kJ kmol-1 K-1
- 10% of the heat required to heat the water is lost in the heat exchanger
- all water entering the system is converted to steam

determine the final outlet temperature of the flue gas and state if the dew point will be reached in both of the cases given in part (j).

(l) Give two advantages of preheating the water in this way and one disadvantage.

(m) Give two reasons why the presence of any sulphur in the fuel mix would be undesirable.

Data:

Net calorific value (MJ m-3) at 25ºC of: Butane (C4H10) = 111.7 MJ m-3
Butene (C4H8) = 105.2 MJ m-3
Propane (C3H8) = 85.8 MJ m-3
Air is 21% oxygen, 79% nitrogen by volume and 23.3% oxygen and 76.7% nitrogen by mass.
Atomic mass of C = 12, O = 16, N=14 and H = 1.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93116050
  • Price:- $45

Priced at Now at $45, Verified Solution

Have any Question? 


Related Questions in Mechanical Engineering

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As