Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

LIFE CYCLE ASSESSMENT

For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle assessment in GaBi. Alternatively, you can perform the LCA manually with known environmental impacts of components. Present the information in a report form as the first Part

Your report should include

a) Write an executive summary
b) Problem definition as an introduction (i.e. service wanted and two alternatives and why you chose this problem) and briefly describe (flow chart is fine) the procedure recommended by the ISO to conduct LCA
c) Estimated weight of each component of each alternative (e.g. plastic type, ink etc. for a white board marker), service life etc. (present in Tabular form)
d) A well-defined functional unit (usually in terms of service, e.g. 100 m of writing).
e) A balancedmaterial flow diagram for each alternative.
f) An impact analysis for each alternative
g) Hot spot identification for each alternative (usually the component or process that gives the most environmental impact from life cycle analysis).
h) Remedial measuresfor the identified hot spot of each alternative and the feasibility ofimprovement options
i) Select the best alternative after the most feasible improvement of each alternative has been implemented and write conclusion.
j) References

ENERGY EFFICIENCY
This section requires you to write a report as a way of answering questions. Please consider a place familiar to you so you can collect data reliably. This could be your office, home, apartment, or room you are living in. Identify one energy consuming appliance in the chosen place. Perform following steps before starting to write the report.

a. Executive summary

b. Problem definition and context as an introduction

c. Identify all relevant information regarding the products(energy consumption rate (kW/h), alternatives, efficiency, usage (hr/d, days per week etc), cost of the device etc.).

d. Find out the sources of energy (gas, coal, electricity, solar) and its cost and environmental impact (especially lookfor carbon emissions per kg or kWh). Provide the emission factor for the state you choose from the state selection guide below.

State selection guide: NSW (ID ending in 0 or 1), SA (ID ending in 2 or 3), VIC (ID ending in 4 or 5), QLD (ID ending in 6 or 7, WA (8 or 9).

e. What organisations (regulatory and/or voluntary) in Australia promote energy efficiency in general and in which wayfor products you use in the chosen place?

f. Identify the opportunities to decrease energy consumption including but not limited to replacement of devices, timer switches, manual switching, programmed switches, off-peak power usage, alternative fuel etc. and select two optionsfor improvement.

g. Perform the cost benefit analysis (simple payback period calculation is sufficient) for three improvement options

h. Conclude the best option of the three in (e). Provide reasoning (i.e., in terms of energy efficiency, cost, environmental benefit)

i. References

Note: For life cycle assessment using "Gabi" software and make a report

In energy efficiency for write answer (D) by choosing state "South Australia"

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93137114
  • Price:- $100

Guranteed 48 Hours Delivery, In Price:- $100

Have any Question? 


Related Questions in Mechanical Engineering

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

1 explain the term critical equipment and provide two clear

1. Explain the term "critical equipment" and provide two clear examples of machinery which falls into this category on board a twin screw motor vessel. 2. Explain the process of Charpy lmpact Testing including sample mar ...

Fluid mechanics assignment - finite control volume analysis

Fluid Mechanics Assignment - Finite Control Volume Analysis and Dimensional Analysis Q1. The wind blows through a 7ft × 10ft garage door opening with a speed of 5 ft/s as shown in the figure. Determine the average speed, ...

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As