Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) What is the significance of LOCK signal in 8086?

2) prepare down the functions of bus interface unit (BIU) in 8086?

3) What is the clock frequency of 8086?

4) What are the two modes of operations present in 8086?

5) Describe the process control instructions

6) Describe REPEAT-UNTIL statements

7) What do you mean by multiprogramming?

8) What is the difference between absolute and linear select decoding?

9) State the three classifications of 8086 interrupts?

10) prepare down the functions of status pins in 8086.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910940

Have any Question? 


Related Questions in Electrical & Electronics

1 explain why rtp cannot be used as a transport-layer

1. Explain why RTP cannot be used as a transport-layer protocol without being run on the top of another transport-layer protocol such as UDP. 2. Both TCP and RTP use sequence numbers. Do sequence numbers in these two pro ...

Assignment questiondesign automatic fan speed controller

Assignment Question Design automatic fan speed controller based on the temperature variation in room using a microcontroller. Abstract: The electronic Circuit used to control the speed of fan based on temperature variati ...

Calculate the approximate diameter and length of stator

Calculate the approximate diameter and length of stator core, the number of stator slots and the number of conductors for a 20KW,400V,3 phase,4pole,1200rpm,delta connected induction motor. Bav=0.5T, Kw=0.82, ac=26000amp. ...

1 why is it necessary to have the minus sign associated

1. Why is it necessary to have the minus sign associated with the time rate of increase of magnetic flux on the right side of Faraday's law? 2. What is electromotive force? 3. What are the different ways in which an emf ...

An initially straight beam ab is bent into a circular arc

An initially straight beam AB is bent into a circular arc A'B' as shown in the figure. The deformation is specified as Where g(X 2 ) is a simple function of X 2 . (a) Find the deformation gradient in terms of g(X 2 ). (b ...

A number equal to the sum of its coordinates is assigned to

A number equal to the sum of its coordinates is assigned to each point in a rectangular room having three of its contiguous edges as the coordinate axes. Draw a sketch of the constant-magnitude surfaces for the number fi ...

Load flow calculation -in the power network shown below

Load Flow Calculation - In the power network shown below, node 1 is the slack bus, where the nodal voltage is defined as (1.0∠0 o ) pu, nodes 2, 4 and 5 are load buses, and node 3 is a generator bus where the voltage mag ...

1 state the divergence theorem and discuss its application2

1. State the divergence theorem and discuss its application. 2. What is the divergence of the curl of a vector? 3. Summarize Maxwell's equations in differential form. 4. Are all Maxwell's equations in differential form i ...

1 state maxwells equations for static fields ina integral

1. State Maxwell's equations for static fields in (a) integral form, and (b) differential form. 2. Discuss the classification of static fields with reference to subsets of Maxwell's equations. 3. Outline the steps involv ...

1 a synchronous alternator is supplying 09 pu power to the

(1) A synchronous alternator is supplying 0.9 p.u. power to the grid when a temporary three-phase short occurs on the interconnector. The power angle curves are:- Pre-fault = 2.0 sin(delta) During fault = 0.5 sin(delta) ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen