+1-415-315-9853

info@mywordsolution.com

Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: What are the different factors which find out the rolling resistance of the train?

problem 2: What do you mean by Adhesion and what are the factors which influence it?

problem 3: What do you mean by the term Balancing Speed?

problem 4: What are the different factors that determine that how much trailing load can be joined to a locomotive?

problem 5: Name the two parameters which find out the starting tractive effort of the locomotive.

problem 6: Name the different parameters which find out the safe lifting load of a crane.

problem 7: Why a match wagon has been given in 140 ton Diesel Breakdown crane?

problem 8: What is the main purpose of outriggers given in a 140 ton diesel breakdown crane?

problem 9: What are the main functions of the Mechanical Department? Name the organization of the Mechanical Department in the Railway Board?

problem 10: Name the organization of the Mechanical Department at Zonal headquarters? Describe the duties of the Mechanical HODs.

problem 11: prepare brief note on any two of the given:

a) DLW
b) CLW
c) ICF
d) DRCF

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M97714

Have any Question?

Related Questions in Mechanical Engineering

Compute the shear strengths of those two threads if the

Compute the shear strengths of those two threads if the fasteners are made from Grade 8 material? Compute the ratio between shear strength and proof strength for each of these two threads ? A threaded fastener will often ...

Question 1derive an expression for the velocity vector of

Question 1: Derive an expression for the velocity vector of the collar D, N V D. The upper arm (B) rotates about a horizontal axis ( nˆ x ) at a rate q · 1 The lower arm (C) Rotates about the longitudinal axis of B (bˆ z ...

1 using the expression for the gradient in polar

1. Using the expression for the gradient in polar coordinates (Appendix A), find the gradient of ψ(r,θ) when Where is the gradient maximum? The terms A and a are constant. 2. Given the following expression for the pressu ...

Introductionemployers are constantly asking for engineering

Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers need to be creative and innovative. They have to ...

Optional extra credit problemyou have been given a map

OPTIONAL EXTRA CREDIT PROBLEM You have been given a map which references a monument having coordinates North 2403306.986, East 5873350.973, expressed in US Survey Feet. A statement on the map states that the area mapped ...

Determine the maximum in-plane stresses for a cylindrical

Determine the maximum in-plane stresses for a cylindrical tank made of steel (E = 205 GPa, ν = 0.30), having a mean radius of 2 m and a thickness of 20 mm, and subjected to an internal pressure p = 1 MPa.

1 two clean and parallel glass plates separated by a gap of

1. Two clean and parallel glass plates, separated by a gap of 1.625 mm, are dipped in water. If σ = 0.0735 N/m, determine how high the water will rise. 2. A glass tube having an inside diameter of 0.25 mm and an outside ...

The viscosity eta of water at various temperatures t is

The viscosity η of water at various temperatures T is given in the following table Compute the cubic splines that pass through the three given points. Evaluate the viscosity at 25°C. The measured value has been reported ...

A steel bar with the cross section shown and effective

A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a compressive load P = 200 kN with a eccentricity e = 0.00625 m. Find (a) the beam's maximum deflection, and (b) the maximum normal ...

Let the texturized si floating gate be modeled by

Let the texturized Si floating gate be modeled by semi-spherical hills. Calculate the radius of the hemisphere that would increase the write/erase time by 100 over the flat poly-Si/SiO2 interface. Use the Fowler-Nordheim ...

• 4,153,160 Questions Asked
• 13,132 Experts
• 2,558,936 Questions Answered

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen