Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

1) describe the need for the irrigation in developing countries?
 
2) describe the term sprinkler irrigation.

3) Describe the meaning of “Duty” and “Delta”.

4) describe the term “evapo-transpiration”?

5) describe the term “water shed cand”?

6) describe the reason behind performing the canal lining?

7) Specify some of the limitations of the Bligh’s theory.

8) Specify different types of spillarcy.

9) describe the term “Aquaduct”?

10) describe the circumstance under which the “Level Crossing” is provided?

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M912343

Have any Question? 


Related Questions in Civil Engineering

Given the elevation of the end shearwall of a building as

Given: The elevation of the end shearwall of a building as shown in Fig. 3.C. The force from the roof diaphragm to the shearwall is 10 k. The wall dead load D = 20 psf, and the seismic coefficient is 0.200. Find: The tot ...

The networks we have used so far in this chapter have not

The networks we have used so far in this chapter have not included a bias vector. Consider the problem of designing a perceptron network (Figure P7.3) to recognize the following patterns: i. Why is a bias required to sol ...

1 could you reduce friction in a pipe by coating the pipe

1. Could you reduce friction in a pipe by coating the pipe wall with Teflon? Why or why not? 2. The flow of water in a 4 mm diameter pipe must remain laminar. Plot a graph of the maximum allowable flowrate as a function ...

The homogeneous cylinder of weight w and radius r rests in

The homogeneous cylinder of weight W and radius R rests in a groove of width 2b. Determine the smallest force P required to roll the cylinder out of the groove. Assume that there is enough friction to prevent slipping.

Suppose we wish to measure the traffic at a point on a

Suppose we wish to measure the traffic at a point on a railroad track, counting the axle crossings in each direction. We set up a light beam just above the rails and place two photocells A and B some inches apart, as sho ...

A divide-by-2 counter has the following specificationdesign

A divide-by-2 counter has the following specification. Design a divide-by-2 (that is, l-bit) counter using only one D flip-flop. You may also include any combinational logic you wish in your design, butry to minimize the ...

The airflow system in prob 760 is measured with a venturi

The airflow system in Prob. 7.60 is measured with a venturi having like dimensions as the orifice, i.e., the same pipe diameter and throat diameter. Calculate the flow rate in kg/s for the same pressure and temperature m ...

Individual assignment- urban drainage designobjectivedesign

Individual Assignment- Urban Drainage Design OBJECTIVE: Design the drainage system (cross-section of channels) for the particular rainfall and given catchment area. OUTCOMES: Design of cross section should be safe for th ...

Suppose that we have the following three reference patterns

Suppose that we have the following three reference patterns and their targets: Each pattern is equally likely. i. Draw the network diagram for an ADALINE network with no bias that could be trained on these patterns. ii. ...

Question if y1 and y2 are alternate depths of a rectangular

Question: If y 1 and y 2 are alternate depths of a rectangular channel show that y c  → Criticle depth 2y 1 ²y 2 ²/(y 1 +y 2 ) = Y c 3 and hence the specific energy, E = (y 1 2 + y 1 y 2 +y 2 2 )/(y 1 + y 2 ) No of Pages ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen