Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Civil Engineering Expert

1. a. prepare down the six significant points to be considered during selecting a site for construction of Dam.

b. describe differential leveling with a neat sketch.

2. describe with neat sketch the different types of piles.

3. List out the different types of bond in brick wall and describe any three in detail.

4. Draw a neat sketch of a reinforced cement concrete column and describe.

5. describe the types of floor suitable for residential and commercial building.

6. describe briefly the different types of pitched roof coverings.

7. Define Dam, Bridge and classify them

8. What are the basic components of a bridge?

9. Define beam, column and Lintel.

10. Classify the types of column based on its conditions.

11. State the purpose of plastering.

12. What is the purpose of reinforced concrete?

13. Describe factor of safety in detail.

Civil Engineering, Engineering

  • Category:- Civil Engineering
  • Reference No.:- M911770

Have any Question? 


Related Questions in Civil Engineering

Consider the general model of a clocked sequential circuit

Consider the general model of a clocked sequential circuit shown in figure 4.12. Suppose that the building blocks are governed by the following parameters: A. What is the minimum clock period that will ensure correct ope ...

1 is it possible for a one-input one-output combinational

1. Is it possible for a one-input, one-output combinational circuit built entirely of two-input NAND gates to contain a hazard? Either draw such a circuit or explain why one cannot be built. 2. Is it possible for a Combi ...

The arm abcd of the industrial robot lies in a vertical

The arm ABCD of the industrial robot lies in a vertical plane that is inclined at 40? to the yz-plane. The arm CD makes an angle of 30? with the vertical. A socket wrench attached at point D applies a 52-lb · ft couple a ...

The four forces shown act on the rollers of an in-line

The four forces shown act on the rollers of an in-line skate. Determine the equivalent force-couple system, with the force acting at O (the ankle joint of the skater).

A divide-by-2 counter has the following specificationdesign

A divide-by-2 counter has the following specification. Design a divide-by-2 (that is, l-bit) counter using only one D flip-flop. You may also include any combinational logic you wish in your design, butry to minimize the ...

1 devise a scheme for representing rational numbers as

1. Devise a scheme for representing rational numbers as binary strings. Briefly describe algorithms for performing addition and comparison using your scheme. 2. Devise a scheme for representing rational numbers and ratio ...

Objectivethe fundamental objectives of this assignment is

OBJECTIVE: The fundamental objectives of this assignment is to demonstrate the student ability to 1. Use the knowledge of different analysis methods learned in lectures to solve the task given in this assessment 2. Use S ...

Consider again the four-class decision problem that we

Consider again the four-class decision problem that we introduced in Problem P4.3. Train a perceptron network to solve this problem using the perceptron learning rule. Problem P4.3 We have a classification problem with f ...

Water is flowing through a circular channel at the rate of

Water is flowing through a circular channel at the rate of 400litres/sec,when the channel is having a bed slope of 1 in 9000.The depth of water in the channel is 8.0 times the diameter.find the diameter of the circular c ...

Consider the gain plot in figure p12-68a find the transfer

Consider the gain plot in Figure P12-68. (a) Find the transfer function corresponding to the straightline gain plot. (b) Use MATLAB to plot the Bode magnitude of the transfer function. (c) Design a circuit that will real ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro