Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Determine the trigonometric Fourier series for the waveform as shown in figure below:

2163_trigonometric fourier series.jpg

problem 2: Determine the trigonometric series for the full wave rectified sine wave as shown in figure below.

1700_trigonometric series.jpg

problem 3: Find out the Fourier transform of a gate pulse of unit height unit width and centered at t = 0.

problem 4: Find out the Fourier transform of the rectangular pulse or gate functions as shown in figure below:

98_fourier transform.jpg

problem 5: What is the Fourier Transform of the rectangular pulse as shown in figure below?

862_rectangular pulse.jpg

problem 6: Determine the Fourier transform of exponential pulse as shown in figure below.

796_exponential pulse.jpg

problem 7: Determine the Fourier transform of triangular pulse as shown in figure below.

635_triangular pulse.jpg

problem 8: Figure below shows the Saw tooth wave form. Determine the exponential Fourier series for this waveform. As well plot the magnitude and Phase spectrum.

1860_saw tooth wave.jpg

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M97577

Have any Question? 


Related Questions in Electrical & Electronics

A 12-bit oversampling adc oversamples by a factor of m 64

A 12-bit oversampling ADC oversamples by a factor of M = 64. To achieve the same average power of the quantization noise at the output, but without using oversampling, how many bits are required?

Consider the simple rc circuit shown in fig p23-3 let r 1

Consider the simple RC circuit shown in Fig. P2.3-3. Let R = 1 kΩ and C = 1 nF. (a) Find the system transfer function. (b) Plot the magnitude and phase responses. (c) Show that a lowpass signal x(t) with bandwidth W « 10 ...

A force f is applied at the tip of the uniform bar shown in

A force F is applied at the tip of the uniform bar shown in the figure. The displacement of the bar is given as u(X) = λX where λ is the principal stretch. The initial length and the cross-sectional area of the bar are, ...

Suppose that a discrete-time system is specified by the

Suppose that a discrete-time system is specified by the transfer function Compute and plot a. The step response of the system b. The impulse response of the system c. The response of the system to the input signal

Data at a rate of 1 million pulses per second are to be

Data at a rate of 1 million pulses per second are to be transmitted over a certain communications channel. The unit step response g(t) for this channel is shown in Fig. P2.7-1. a. Can this channel transmit data at the re ...

Consider a pv array charging batteries for an off-the-grid

Consider a PV array charging batteries for an off-the-grid, stand-alone system near Boulder, Colorado You plan to run everything in the house on 120 V ac. a. Suppose the load is estimated to consist of the following 120 ...

1 discuss how the cutoff condition arises in a waveguide2

1. Discuss how the cutoff condition arises in a waveguide. 2. Explain the relationship between the cutoff wavelength and the spacing between the plates of a parallel-plate waveguide based on the phenomenon at cutoff.

For a system specified by the transfer functionwrite sets

For a system specified by the transfer function write sets of state equations for DFII and its transpose, cascade, and parallel forms. Also write the corresponding output equations.

1 find the velocity with which the group of two frequencies

1. Find the velocity with which the group of two frequencies 2400 MHz and 2500 MHz travels in a parallel-plate waveguide of dimension a = 2.5 cm and having a perfect dielectric of 2. For a narrow-band amplitude modulated ...

Tasks1learn how to use opendss2open and execute the epri

Tasks 1. Learn how to use OpenDSS 2. Open and execute the EPRI Test Circuit 24 model 3. Develop base case data sets of bus voltages and power flows 4. Provide analysis of the base case model: a. Feeder voltage profiles b ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro