Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Part 1

You are required to design a product and to present your final design solution as a poster.
The project should be presented in a professional fashion by the due date in an A-1 sized poster (594 mm x 841 mm). Make sure your names and AUT ID numbers are clearly shown on the front of your poster.

Human powered vehicle (HPV) Speed record

Part 2

a) Respond to the critiques from part i by improving your design

b) Develop the design further by considering issues including at least two of:

i. Design optimisation

ii. Costing

iii. Strength

iv. Balance and stability

v. Performance such as: speed, mileage, endurance, efficiency and so on

c) Prepare more detailed design drawings and engineering calculations than in Part 1

d) Document your final design in an A1 sized poster (594 mm x 841 mm)

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9598

Have any Question? 


Related Questions in Mechanical Engineering

A w10 times 45 beam is made of structural steel and used as

A W10 × 45 beam is made of structural steel and used as a column with a length 15 ft. If its ends are fixed, can the column support the critical load without yielding? (Thedesignation W10 × 45 provides specifications abo ...

Hydraulic circuit pressure dropthe hydraulic circuit shown

Hydraulic Circuit Pressure Drop The hydraulic circuit shown involves a pump and four pressure restrictions. Assuming the reservoir is at atmospheric pressure and the flow is at steady-state, determine the gage pressures ...

For the allen wrench of problem 715 what is the deflection

For the allen wrench of Problem 7.15, what is the deflection of the tip of the wrench when the maximum load of 60 N is applied, just before the bolt loosens? Problem 7.15: The maximum force applied to the tip of the alle ...

Suppose that the performance of a bjt transistor is

Suppose that the performance of a BJT transistor is entirely limited by emitter injection efficiency, which limits the d.c. beta, and base spreading resistance, which limits the bandwidth. Show that the gain-bandwidth pr ...

1 for the pipe-flow-reducing section d1nbsp 8 cm d2nbsp 5

1. For the pipe-flow-reducing section D 1  = 8 cm, D 2  = 5 cm, and p 2  = 1 atm. If v 1  = 5 m/s and the manometer reading is h =58 cm, estimate the total force resisted by the flange bolts. 2. An open tank car as shown ...

Determine the effective moment and vertical shear force

Determine the effective moment and vertical shear force that would be required to replicate the effect of the three bar forces in Problem 1.15. Problem 1.15: For the truss shown, find the bar forces at the section indica ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

A gas sample is known to be a mixture of ethane and butane

A gas sample is known to be a mixture of ethane and butane. A bulb having a 230.0 cm 3 capacity is filled with the gas to a pressure of 97.5 X 10 3 Pa at 23.1°C. If the mass of the gas in the bulb is 0.3554 g, what is th ...

A 1 in times 10 in plank on a redwood deck has l 48 in

A 1 in × 10 in plank on a redwood deck has L = 48 in long and supported on three joists that rest on the ground and so do not bend. The joists act as pin/roller supports for the plank. If a 130 lb person stands on the pl ...

1 calculate the following for the function fx e-3x - 2xa

1) Calculate the following for the function f(x) = e -3x - 2x. a. Calculate the derivation of the function by hand. Write a MATLAB function that calculates the derivative of this function and calculate the derivative at ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen