Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

You are an engineer for WhyShopHere Toys. You have been tasked with the following:

Design a child's toy to provide food for fish in an aquarium. The toy should take the form of a Rube Goldberg device, with a minimum of 5 steps to deliver the food into the aquarium.

Problem Definition:

  • The device must attach to or interface with "standard" aquariums. A typical aquarium has a 10-gallon capacity. (My son's aquarium, which is slightly smaller than 10 gallons, has the following dimensions: 8" x 16", depth of 10 ½ ". It also has a ½" lip at the top.)
  • The overall device (not including the aquarium) should fit in a volume no larger than 2 cubic feet.
  • The target consumer is a 5-10 year old child. (Hint: You need to expand this statement into as many customer requirements as you can think of. For example, "brightly colored" could be one of the requirements.)
  • Safety must be taken into consideration.

 Refer back to the design process lecture. This project will cover the first 3 steps of the process:

  1. Problem definition (this is where the customer requirements are identified)
  2. Specification development (this is when the customer requirements are re-stated as engineering specs. Remember, engineering specs must be measurable.)
  3. Concept design (represented graphically)

The first 2 steps will be presented through the completion of a QFD chart. The third step will be presented as isometric hand sketches.

 

Deliverables:

A QFD chart, showing the relationships between the customer requirements and the engineering specifications. (Refer to the Ullman QFD chart posted on MyCourses as an example.)

    1. You do NOT need to include the bench mark columns.
    2. You also do NOT need the engineering specs for the bench marks, which are the last 2 rows in the Ullman example.
    3. You should think of as many customer requirements (minimum of 10) and engineering specifications (minimum of 7) as you can.
    4. Remember- engineering specifications must be measurable! You must include target values (with units) for all your engineering specs.
    5. You do NOT need to include manufacturing type customer requirements, such as those in the last 6 rows of the example chart.
    6. To determine the relative importance or weighting of the customer requirements, you first determine which of the requirements in the list are absolute musts. (If the musts are not met, the design is useless.) The must requirements are not included in the weighting scheme. They are identified by an asterisk in the Weighting column in the Ullman example. The requirements that remain are considered wants, and weighted according to relative importance. You may use any technique you wish to determine the relative importance; one such method is pairwise comparison.
    7. The cells in the center portion of the chart represent how each engineering specification relates to each customer requirement. The strength of the relationship can vary, with some engineering specs providing strong measures for a customer's requirement and others providing no measure at all. This relationship is conveyed through numerical values as follows:
    1. 9 = strong relation
    2. 3 = medium relation
    3. 1 = weak relation
    4. Blank = no relation at all
  • A minimum of 3 different concept designs, described briefly in a Word document, and shown graphically as neat isometric hand sketches, on isometric sketch paper. You may also want to include a multiview orthographic sketch of each design as well, or a second isometric sketch from a different view point. The written descriptions should include an explanation of the operation of the device, and a list of the major components.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9528566

Have any Question?


Related Questions in Mechanical Engineering

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

Problem on shaft -assuming no frictional losses a torque of

Problem on Shaft - Assuming no frictional losses, a torque of T = 750lb·in is applied through the shaft of gear F in order to drive the roller chain at point B at a constant speed. The chain sprocket has a pitch diameter ...

Question - truss structureconsider the three membered

Question - Truss Structure Consider the three membered planar truss structure shown in the figure below. All members of the truss have identical square cross-sectional area (A) of 25 mm x 25 mm, and Youngs Modulus (E) = ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As