+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1:

How the hysteresis loss and eddy current loss are reduced in DC machines?

problem 2:

prepare the EMF equation of the DC generator.

problem 3:

Why the efficiency of transformer is superior to any other electrical machines?

problem 4:

Describe the situations for maximum efficiency for a transformer.

problem 5:

A 8 pole, 3 phase induction motor is supplied from 50 Hz, ac supply .On full load, the frequency of induced e.m.f in rotor  is 2 Hz. Find out the full load slip.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M913643

Have any Question?

## Related Questions in Mechanical Engineering

### 1 in a hartree-fock scf calculation on the chlorine atom

1. In a Hartree-Fock SCF calculation on the chlorine atom using 20 (spatial) basis functions, how many virtual orbitals are determined? 2. Give an example of a restricted Hartree-Fock wavefunction and an unrestricted Har ...

### 1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

### The maximum force applied to the tip of the allen wrench

The maximum force applied to the tip of the allen wrench before the bolt loosened is 60 N. Assume the wrench has a circular cross section with a radius 2 mm. The length of the short segment (touching the screw) is 3 cm a ...

### You need a reort if 10 pages and above the report about

You need a reort if 10 pages and above. the report about colorimeter specificly measuring spesific heat. anything you need will be provided. format sample has been will be provided. and a report sapmle will be provided t ...

### 1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

### 1 a venturi meter with an inlet diameter of 06 m is

1. A Venturi meter with an inlet diameter of 0.6 m is designed to handle 6 m3 /s of standard air. What is the required throat diameter if this flow is to give a reading of 0.10 m of alcohol in a differential manometer co ...

### The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

### Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

### Derive a counterpart for the case of plane strain in the

Derive a counterpart for the case of plane strain in the xz-plane of the compatibility equation shown in Problem 4.15 for plane stress. How does this plane strain result differs from the compatibility equation for plane ...

### A 1 in times 10 in plank on a redwood deck has l 48 in

A 1 in × 10 in plank on a redwood deck has L = 48 in long and supported on three joists that rest on the ground and so do not bend. The joists act as pin/roller supports for the plank. If a 130 lb person stands on the pl ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen