Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem1) Compute the essential rotational speed N for the aerial ride in an amusement park in order that the arms of the gondolas will assume an angle ? = 60° with the vertical. Neglect the mass of the arms to which the gondolas are attached and treat each gondola as a particle.

problem2) prepare the dynamic equation and find the transfer functions for the circuits shown in the figure give below:

1106_Circuit.jpg

problem3) Make 3rd angle orthographic sketch of the figure given below:

258_Orthographic projection.jpg

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93894

Have any Question? 


Related Questions in Electrical & Electronics

1 what is the magnetic flux crossing an infinitesimal

1. What is the magnetic flux crossing an infinitesimal surface oriented parallel to the magnetic flux density vector? 2. For what orientation of the infinitesimal surface relative to the magnetic flux density vector is t ...

Does a large bolt-to-joint stiffness ratio increase or

Does a large bolt-to-joint stiffness ratio increase or decrease the possibility of fatigue failure of the bolt and why? Name at least three bolt, thread, or bolt and thread configurations which can improve the fatigue re ...

The device in the schematic diagram below is a viscosity

The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary case. The case and the drum are concentric. Fluid enters at A, flows through the annulus between the ca ...

Determine the maximum film velocity in problemproblem

Determine the maximum film velocity in Problem. Problem Aviscous film drains uniformly down the side of a vertical rod of radius R. At some distance down the rod, the film approaches a terminal or fully developed flow su ...

1 for the force field f x2ay find the approximate value of

1. For the force field F = x 2 ay, find the approximate value of the line integral of F from the origin to the point (1, 3, 0) along a straight line path by dividing the path into ten equal segments. 2. For the force fie ...

1 list the components of a traffic conditioner in diffserv2

1. List the components of a traffic conditioner in DiffServ. 2. Is the flow label in IPv6 more appropriate for IntServ or DiffServ?

A bug starts at a point and travels 1 m northwardm

A bug starts at a point and travels 1 m northward, m eastward, m southward, m westward, m northward, and so on, making a 90°-turn to the right and halving the distance each time. (a) What is the total distance traveled b ...

1 how do you find the work done in moving a test charge by

1. How do you find the work done in moving a test charge by an infinitesimal distance in an electric field? 2. What is the amount of work involved in moving a test charge normal to the electric field? 3. What is the phys ...

Consider a deformation of a rectangular bar whose deformed

Consider a deformation of a rectangular bar whose deformed geometry is given as x 1 = αX 1 , x 2 = βX 2 , x 3 = βX 3 When the material is an incompressible Mooney-Rivlin hyperelastic material with A 10  = 80 MPa and A 01 ...

Write a paper to summarize a literature article for less

Write a paper to summarize a literature article for less than a page and its about a shoe taking power from piezo discussion. Article: Piezoelectric Materials Used in Underwater Acoustic Transducers by Huidong Li, Z. Dan ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen