Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: Describe the properties of fluids?

  • Density
  • Weight density
  • Specific volume
  • Viscosity
  • Surface Tension
  • Capillarity

problem 2: prepare the difference between simple manometers and differential manometers?

problem 3: Derive Pascal law and Hydrostatic law?

problem 4: The space between two square flat parallel plates is filled with oil. Each side of the plate is 60 cm. The thickness of the oil film is 12.5 mm. The upper plate that moves at 2.5 m/s needs a force 98.1 N to maintain the speed. Find out:

a) Dynamic viscosity of the oil in poise.
b) Kinematic viscosity of the oil in stokes if the specific gravity of oil is 0.95.

problem 5: A differential manometer is joined at the two point A & B of two pipes as shown in figure. The pipe A contains a liquid of sp. gr. = 1.5; while B contains of liquid of sp. gr. = 0.9 pressures at A & B are 1kg/cm2 & 1.80 kgf/cm2 respectively. Find out the difference in mercury level in differential manometer.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93564

Have any Question? 


Related Questions in Mechanical Engineering

An isotopically enhanced sample has ndi moles of deuterated

An isotopically enhanced sample has nDI moles of deuterated hydrogen iodide and nHI moles of common HI at 398 K. Comparison of the infrared intensities of the v = 1 S 2 transition inds a ratio of 0.100 for DI molecules ( ...

Instead of the perturbation being switched linearly it was

instead of the perturbation being switched linearly, it was switched on and off exponentially and slowly, the switching off commencing long after the switching on was complete. Calculate the probabilities, long after the ...

1 concrete rocks and bone are strong in compression and are

1. Concrete, rocks, and bone are strong in compression and are usually designed for compressive loading. To test their strength in compression, what sort of test specimen would be useful? 2. Suppose that a downward force ...

Write an engineering paper talking about nano-structure gas

Write an engineering paper talking about Nano-structure gas sensors. I have an outline that I need you to follow and Also I provided all the sources you need to write the paper. High performance nano-structured Zinc Oxid ...

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

1 a venturi meter with an inlet diameter of 06 m is

1. A Venturi meter with an inlet diameter of 0.6 m is designed to handle 6 m3 /s of standard air. What is the required throat diameter if this flow is to give a reading of 0.10 m of alcohol in a differential manometer co ...

A gas sample is known to be a mixture of ethane and butane

A gas sample is known to be a mixture of ethane and butane. A bulb having a 230.0 cm 3 capacity is filled with the gas to a pressure of 97.5 X 10 3 Pa at 23.1°C. If the mass of the gas in the bulb is 0.3554 g, what is th ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

A nut having an effective length of 2 in and a 12-16 un

A nut having an effective length of 2 in. and a 1/2-16 UN thread is snug tightened and then turned 308. How much preload will that create in the bolt? Is that an acceptable preload? Describe the typical torque-turn tight ...

If the speed of the shaft is doubled in given problem what

If the speed of the shaft is doubled in given Problem, what will be the percentage increase in the heat transferred from the bearing? Assume that the bearing remains at constant temperature. Problem An automobile cranksh ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro