Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1) Sketch the following threads taking pitch = 15 mm.

a) Multiple start threads

b) Buttress thread sections

c) Knuckle thread sections

problem 2) Sketch front view and side view of a square headed bolt of 30 mm diameter and 120 mm length with a washer and a hexagonal nut.

problem 3)i) Sketch or sketch free hand any two of the following locking devices:

a) Castle nut

b) Sawn nut

c) Split pin lock nut 9

ii) Sketch freehand any three various types of machine screws.

problem 4) prepare steps to draw a knuckle joint using CAD software.

problem 5) Draw the top view and sectional front view of a single riveted double cover butt joint taking diameter of the rivet = 25 mm.

problem 6)a) Give drawings of any three keys and two different cotters.

b) Draw any five rivet heads and name them.

problem 7) Sketch front view and side view of sleeve and cotter joint. You may use instruments or sketch free hand.

problem 8) Provide conventional representation of left hand and right hand external threads.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98120

Have any Question? 


Related Questions in Mechanical Engineering

Define the endurance limit of a bolt which is greater the

Define the endurance limit of a bolt ? Which is greater, the static yield strength or the endurance limit of the bolt? When will an increase in preload increase fatigue life? When will an increase in preload decrease fat ...

A sample of he ions is prepared at a temperature of 298 k

A sample of He + ions is prepared at a temperature of 298 K and a density of 2.0 # 10 10 cm -3 . Because these are ions, magnetic ields may be used to trap those ions with kinetic energy less than some threshold value et ...

Name the principal modes of failure of both tensile and

Name the principal modes of failure of both tensile and shear joints? Describe or list the criteria a bolted joint designer must consider when selecting bolt size and material for a new joint? Will short, fat bolts gener ...

1 develop three scenarios for comparable circular cylinders

1. Develop three scenarios for comparable circular cylinders of radius R and square tubes of side H that allow one to say R ∼ H. (Hint: What geometric attributes of the cylinder and tube might be made equal?) 2. If a str ...

A small three-phase ig has the following nameplate data 110

A small three-phase IG has the following nameplate data: 110 V, 1.140 rpm, 60 Hz, Y connection, and 1250 W. The blocked rotor test at 60 Hz yielded the following: I = 69.4 A, P = 4200 W. The turn ratio between stator and ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

There are 3 x 103 spheres in a box calculate the number of

There are 3 x 10 3 spheres in a box. Calculate the number of different combinations for the spheres in order to have 1100 spheres in the front third of the box. Assuming that the distribution is normal, calculate the pro ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

As can often be seen in a kitchen sink when the faucet is

As can often be seen in a kitchen sink when the faucet is running, a high-speed channel flow (v 1 , h 1 ) may ''jump'' to a low-speed, low-energy condition (v 2 , h 2 ). The pressure at sections 1 and 2 is approximately ...

The dc beta rises with collector current due to the sns

The d.c. beta rises with collector current due to the SNS effect and drops due to high injection level in the best. Combine these two effects and obtain the condition at which the beta peaks. Use the simplest formulas de ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen