Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe the term permeability and reluctivity of the magnetic material.

2) prepare some of the differences between Hard and Soft Magnetic Material.

3) Develop the construction diagram of the slug tuned inductor. Specify some of its applications.

4) describe the types of inductors and discuss what ferrite core inductor is?

5) describe why the iron core inductor is better in comparison to the air core inductors.

6) State some of the characteristics of cable.

7) Design the sketch of co-axial cable and state some of its applications.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911853

Have any Question? 


Related Questions in Electrical & Electronics

When bill clinton took office in january 1993 he faced two

When Bill Clinton took office in January 1993, he faced two major economic problems: a large federal budget deficit and high unemployment resulting from a very slow recovery from the recession of 1990 to 1991. In his fir ...

1 what is snells law2 what is meant by the plane of

1. What is Snell's law? 2. What is meant by the plane of incidence? Distinguish between the two different linear polarizations pertinent to the derivation of the reflection and transmission coefficients for oblique incid ...

1 we discuss the use of sip in this chapter for audio is

1. We discuss the use of SIP in this chapter for audio. Is there any drawback to prevent using it for video? 2. Assume two parties need to establish IP telephony using the service of RTP. How can they define the two ephe ...

1 a rectangular block of concrete 3 ft times 3ft times 6 in

1. A rectangular block of concrete 3 ft × 3ft × 6 in. has its 6- in. side half buried at the bottom of a lake 23 ft deep. What force is required to lift the block free of the bottom? What force is required to maintain th ...

Consider a nonlinear elastic uniaxial bar element under tip

Consider a nonlinear elastic uniaxial bar element under tip force F = 100 N shown in Figure. The stress-strain relation is given in terms of Cauchy stress and engineering strain in the deformed geometry: σ11 = Eε 11 . Us ...

In a real-time multimedia communication assume we have one

In a real-time multimedia communication, assume we have one sender and ten receivers. If the sender is sending multimedia data at 1 Mbps, how many RTCP packets can be sent by the sender and each receiver in a second? Ass ...

1 explain the term internal inductance2 what is meant by

1. Explain the term internal inductance. 2. What is meant by the quasistatic extension of the static field in a physical structure? 3. Outline the steps involved in the electroquasistatic field analysis of a parallel pla ...

1 oil is supplied at the center of two long plates the

1. Oil is supplied at the center of two long plates. The volumetric flow rate per unit length is Q and the plates remain a constant distance, b, apart. Determine the vertical force per unit length as a function of the Q, ...

1 find the minimum value of h for which the gate shown

1. Find the minimum value of h for which the gate shown will rotate counterclockwise if the gate cross section is (a) rectangular, 4 ft × 4 ft; (b) triangular, 4 ft at the base × 4 ft high. Neglect bearing friction. 2. A ...

1 what is the expansion for the divergence of a vector2

1. What is the expansion for the divergence of a vector? 2. State Gauss' law for the magnetic field in differential form. How is it derived from its integral form? 3. How can you determine if a given vector can represent ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro