Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) What are the necessary features of a hydro-electric power plant? describe the different types of dams used in such plants?

problem 2) prepare down the various methods of ash handling. describe the pneumatic system of ash handling. Why it is necessary to quench the ash before handling?

problem 3) prepare down the advantages and disadvantages of gas turbine plant over steam power plant? Describe the working of combined steam and gas power plant.

problem 4) How nuclear waste is disposed off, name the difficulties in handling radioactive waste?

problem 5) describe the working of solar thermal power generation, with neat and well labelled diagram

problem 6) What are various kinds of reactor commonly used? describe the fast breeder reactor. prepare down the advantages over sodium graphite reactor?

problem 7) What do you mean by load curve? prepare down its importance in power generation?

problem 8) What do you mean by tariff? What are the types of tariffs? Describe the two part tariff.

problem 9) describe run-off in detail. Describe the factors affecting run-off.

problem 10) describe the methods to find run-off.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98938

Have any Question? 


Related Questions in Mechanical Engineering

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

Describe the mil-std-1312 nas test name three generic ways

Describe the MIL-STD-1312 (NAS) test? Name three generic ways to prevent or at least minimize self-loosening? Define prevailing torque? A proper length-to-diameter ratio for the bolt can reduce or eliminate self-loosenin ...

A cantilever beam ab supports a uniform load of intensity q

A cantilever beam AB supports a uniform load of intensity q acting over part of the span and a concentrated load P acting at the free end, as shown. Determine the deflection and slope at end B of the beam. The beam has l ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

The illustration below shows a vane with a turning angle

The illustration below shows a vane with a turning angle θ which moves with a steady speed v c . The vane receives a jet that leaves a fixed nozzle with speed θ. (a) Assume that the vane is mounted on rails as shown in t ...

1 calculate and confirm the maximum bending stress of the

1. Calculate and confirm the maximum bending stress of the stainless steel nail plate given above. 2. Research and identify the major materials compatibility issues that arise when devices such as the nail plate are inse ...

The maximum force applied to the tip of the allen wrench

The maximum force applied to the tip of the allen wrench before the bolt loosened is 60 N. Assume the wrench has a circular cross section with a radius 2 mm. The length of the short segment (touching the screw) is 3 cm a ...

How do bolt stiffness and joint stiffness affect the angle

How do bolt stiffness and joint stiffness affect the angle of turn versus preload relationship? A rubber washer has been used instead of a metal one, by mistake. How will preload be affected if the same predetermined tor ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

Confirm that in hydrogenic atoms the spin-orbit coupling

Confirm that in hydrogenic atoms, the spin-orbit coupling constant depends on n and l as in eqn 7.24 2.Calculate the spin-orbit coupling constant for a 2p-electron in a Slater-type atomic orbital, and evaluate it for the ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro