Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Add and multiply the number given below in the given base without converting to decimal.

(a) (387)8    (b)    (715)8

2) What is meant by Error-Detection codes? describe it with suitable ex.

3) Show by means of Truth Table, the validity of theorem of Boolean algebra.

(a) The Associative laws.

4) Determine F’ using De Mogan’s theorem where:

F = B’D’ + B’C’ + A’C’D

5) Describe which gates are called universal Gate? describe why in detail?

6) What do you mean by Demultiplexer? describe it with suitable ex. prepare down two applications.

7) describe State Reduction with suitable ex.

8) Describe Asynchronous counters with suitable ex.

9) prepare down the difference between Static and Dynamic RAM.

10) prepare down the Recording Techniques used in secondary storage device.

11) Describe 4-bit carry – look ahead adder with suitable logic diagram.

12) Draw a counter with the binary sequence: 0, 1, 3, 7, 6, 4 and repeat. Use t Flip-flops.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913006

Have any Question? 


Related Questions in Electrical & Electronics

1 how do you find the approximate value of the surface

1. How do you find the approximate value of the surface integral over a given surface? 2. How do you find the exact value of the surface integral? 3. Provide physical interpretations for the closed surface integrals of a ...

A voltage source vt 100 cos2pi50 t v is applied to a

A voltage source v(t) = 100 cos(2π50 t) [V] is applied to a nonlinear load, resulting in non-sinusoidal current: i(t) = 4 + 10 cos(2π50 t +30°) + 20 cos (4π50 t +45°) [A]. Determine: (a) the power absorbed on the load, ( ...

1 if the ram and auto rack in the previous problem together

1. If the ram and auto rack in the previous problem together have a mass of 680 kg, estimate the maximum sinking speed of the ram and rack when gravity and viscous friction are the only forces acting. Assume 2.44 m of th ...

1 describe the phenomenon of the bouncing back and forth of

1. Describe the phenomenon of the bouncing back and forth of transient waves on a transmission line excited by a constant voltage source in series with internal resistance and terminated by a resistance. 2. Discuss the v ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

1 in jpeg explain why we need to round the result of

1. In JPEG, explain why we need to round the result of division in the quantization step. 2. Explain why the combination of quantization/dequantization steps in JPEG is a lossy process even though we divide each element ...

A module with 40 cells has an idealized rectangular i-v

A module with 40 cells has an idealized, rectangular I-V curve with I SC = 4 A and V OC = 20 V. If a single cell has a parallel resistance of 5Ω and negligible series resistance, draw the I-V curve if one cell is complet ...

1 two immiscible fluids of different density and viscosity

1. Two immiscible fluids of different density and viscosity are flowing between two parallel plates. Express the boundary conditions at the interface between the two fluids. 2. Determine the velocity profile for fluid fl ...

An euler beam element shown in the figure is under a

An Euler beam element shown in the figure is under a uniformly distributed couple, C. Calculate the equivalent nodal forces. Using a simply supported beam under a uniform couple, show that the reaction forces are equal a ...

The device in the schematic diagram below is a viscosity

The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary case. The case and the drum are concentric. Fluid enters at A, flows through the annulus between the ca ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen