Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) What do you mean by Gauge?

2) prepare down the advantages and disadvantages of the welded joint.

3) What is meant by buckling?

4) prepare down the modes of failures of columns?

5) What is the permissible deflection of a steel beam as per BIS?

6) Describe how will you compute the effective length of a compression flange in steel beam?

7) What is meant by staging?

8) Determine the minimum thickness of steel sections recommended by BIS to prevent corrosion?

9) prepare down the functions of purlins?

10) prepare down the procedure for design of purlin when slope of roof is less than 30o.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913201

Have any Question? 


Related Questions in Mechanical Engineering

1 the hypodermic needle shown below contains a liquid serum

1. The hypodermic needle shown below contains a liquid serum (ρ = 1 g/cm 3 ). If the serum is to be injected steadily at 6 cm 3  /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is negl ...

What is a cryogenic bolt materialwhich definition of

What is a cryogenic bolt material? Which definition of strength are we most often concerned about when selecting a joint configuration or material? Name the two committees who manage ASTM bolting standards.

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

The probability of a linear molecule being in a particular

The probability of a linear molecule being in a particular rotational level J depends on the temperature, and for J 7 0 there is a temperature Tmax at which the probability for that level reaches a maximum. Derive an exp ...

A steel bar with the cross section shown and effective

A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a compressive load P = 200 kN with a eccentricity e = 0.00625 m. Find (a) the beam's maximum deflection, and (b) the maximum normal ...

If you were using a full length centerline gage rod to

If you were using a full length, centerline, gage rod to measure DL, how much change would you expect to see at 2508F?  What DL from ‘‘before tightening'' would you expect to see at 2508F if you were using ultrasonics to ...

An athlete at high performance inhales of air at 100 atm

An athlete at high performance inhales of air at 1.00 atm and 298 K. The inhaled and exhaled air contain 0.50 and 6.2% by volume of water, respectively. For a respiration rate of 32 breaths per minute, how many moles of ...

1 sketch the deformation of a fluid element for the

1. Sketch the deformation of a fluid element for the following cases: 2. For a two-dimensional, incompressible flow with velocity v x  = v x (y), sketch a three-dimensional fluid element and illustrate the magnitude, dir ...

Extend the analyses of the three narrow-gate effects to

Extend the analyses of the three narrow-gate effects to include the voltage dependent bulk charge. Give two numerical examples using the submicron transistors of problem P685.5. Problem P685.5 Extend the analyses of the ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro