+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

1) What do you mean by obligatory point?

2) What is meant by map study?

3) describe the modulus of elasticity of subgrade in detail.

4) What do you understand by dowel bars?

5) Describe CBR in detail.

6) What is meant by flakiness index?

7) What do you mean by reflection cracking?

8) What do you understand by pavement serviceability?

9) Describe internal rate of return in detail.

10) prepare down about BOT projects in detail.

11)a) Exp[lain the initial survey for highway alignment. prepare down the data to be collected.

b) prepare down the materials that are used in the bituminous road? Describe its construction procedure in detail.

12)a) What is meant by Road development plan? prepare down the features of Third Road Development plan in detail.

b) describe the construction procedure of the WBM road.

Civil Engineering, Engineering

• Category:- Civil Engineering
• Reference No.:- M912684

Have any Question?

## Related Questions in Civil Engineering

### The figure shows a schematic of a torsion-bar suspension

The figure shows a schematic of a torsion-bar suspension for an auto mobile (the torsion bar appears in cross section at A). If the three forces and the couple C = 900 lb · ft are equivalent to a upward vertical force R ...

### A common approach to the addition of nbit binary numbers

A common approach to the addition of n,bit binary numbers uses n cascaded combinational modules, each a l-bit adder (conventionally called a full adder). Full-adder modules can be combined as follows to implement a circu ...

### 1 water flows in a 5-in-diameter pipe at 20c with a mean

1. Water flows in a 5-in-diameter pipe at 20?C with a mean flow velocity of 3 m/s. A sharp-edged orifice with a diameter of 2.5 in is to be used to measure the flow rate. What pressure differential would be indicated for ...

### A water treatment plant has four clarifiers treating 80 mgd

A water treatment plant has four clarifiers treating 8.0 MGD (0.350 m 3 /sec) of water. Each clarifier is 16 ft (4.88 m) wide, 80 ft (24.4 m) long, and 15 ft (4.57 m) deep. Determine: A. The detention time (hr) B. Overfl ...

### If the uncertainties in temperature and pressure for prob

If the uncertainties in temperature and pressure for Prob. 7.49 are ±1.5?F and ±2 kPa, respectively, what is the uncertainty of the billing if the actual volume flow measurement is exact? Prob. 7.49 A positive-displaceme ...

### Suppose we wish to measure the traffic at a point on a

Suppose we wish to measure the traffic at a point on a railroad track, counting the axle crossings in each direction. We set up a light beam just above the rails and place two photocells A and B some inches apart, as sho ...

### Barracks logic is built out of sleeping soldiers covered by

Barracks logic is built out of sleeping soldiers covered by electric blankets. Each blanket has a control switch with discrete control settings ranging in S-degree (Fahrenheit) intervals from 0 to SO degrees. The tempera ...

### Based on the values you calculated in problem 208 answer

Based on the values you calculated in Problem 20.8, answer and explain the following: a. In which vessels should elasticity of the vessel be considered? b. In which vessels should the non-Newtonian behavior of blood be c ...

### The step response of a linear circuit isa is the circuit a

The step response of a linear circuit is (a) Is the circuit a low-pass, high-pass, bandpass, or bandstop filter? (b) Construct the straight-line Bode gain plot and estimate the cutoff frequency and passband gain. (c) Use ...

### A divide-by-2 counter has the following specificationdesign

A divide-by-2 counter has the following specification. Design a divide-by-2 (that is, l-bit) counter using only one D flip-flop. You may also include any combinational logic you wish in your design, butry to minimize the ...

• 4,153,160 Questions Asked
• 13,132 Experts
• 2,558,936 Questions Answered

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen