Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

What is the need for the controller?

problem 2:

prepare down the fundamental elements of pneumatic systems.

problem 3:

prepare down the transfer functions of the PI and PID controllers.

problem 4:

prepare down the components of the typical feedback control system.

problem 5:

Illustrate out the steady state and transient response.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912450

Have any Question? 


Related Questions in Mechanical Engineering

1 two clean and parallel glass plates separated by a gap of

1. Two clean and parallel glass plates, separated by a gap of 1.625 mm, are dipped in water. If σ = 0.0735 N/m, determine how high the water will rise. 2. A glass tube having an inside diameter of 0.25 mm and an outside ...

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

The concentric joint of problem is subjected to an increase

The concentric joint of problem is subjected to an increase in temperature of 1008F. Does this increase or decrease the tension in the bolts? By how much? (Assume that the coefficient of linear expansion of the bolts is ...

I need a proposal project for surface metrology asap i need

I need a proposal project for Surface Metrology ASAP. I need two documents: 1. Project outlines Proposal outlines (the instruction & template is in the attached Proposal for the project) should be 1 page 2. Final project ...

A uniform cantilever beam with triangular cross section is

A uniform cantilever beam with triangular cross section is loaded only due to its own weight (a load uniformly distributed along the length). What is the ratio of the maximum tensile normal stress to the maximum compress ...

Assignmentfor this homework you will be creating scripts in

ASSIGNMENT For this homework you will be creating scripts in SciLab. You will turn in electronically, each of the scripts requested below. This is not a group project, so do your own work. Contact me if you have any ques ...

A stationary jet engine is shown air with a density of

A stationary jet engine is shown. Air with a density of 0.0805 lb m /ft 3  enters as shown. The inlet and outlet cross-sectional areas are both 10.8 ft 2 . The mass of fuel consumed is 2% of the mass of air entering the ...

For a deck supports of length 325 m are proposed to be

For a deck, supports of length 3.25 m are proposed to be built from aluminum with a Young's modulus of 72 GPa and a yield stress of 480 MPa. A cylindrical design is proposed with outer diameter d = 100 mm and wall thickn ...

Q1 a list three classical methods of optimization in

Q1) a) List three classical methods of optimization in engineering design. b) Describe the type of finite elements used to solve 3 dimensional problems in solid mechanics. Supply examples of the application. c) Describe ...

A strain gage is installed as shown on an aluminum soda can

A strain gage is installed as shown on an aluminum soda can. The can's radius is 1.3 in and its wall thickness is 0.004 in (sometimes written as 4 mil; 1 mil = 1/1000 in). When the lid of the can is opened, the magnitude ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen