Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) prepare down the factors that are affecting the schedule speed of a train.

2) prepare down the difference between dead weight and accelerating weight of a locomotive?

3) What do you understand by tractive effort?

4) prepare down the advantages of electric braking.

5) Why three phase traction system employing induction motors is now obsolete give reasons?

6) prepare down the different types of braking methods.

7) Describe the current trends in AC traction systems?

8) prepare down the advantages of pantographs?

9) (a) Draw the typical speed-time curve for (1) Main line service and to sub – urban services in electric Traction.

(b) Describe the mechanics of train movement in detail.

10)(a) What is multiple unit control in electric train and describe each one of them in detail?

(b) What are various braking systems and describe them in detail?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911471

Have any Question? 


Related Questions in Mechanical Engineering

The figure illustrates the operation of an air lift pump

The figure illustrates the operation of an air lift pump. Compressed air is forced into a perforated chamber to mix with the water so that the specific gravity of the air-water mixture above the air inlet is 0.5. Neglect ...

1 concrete rocks and bone are strong in compression and are

1. Concrete, rocks, and bone are strong in compression and are usually designed for compressive loading. To test their strength in compression, what sort of test specimen would be useful? 2. Suppose that a downward force ...

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

Use eqn 135 to find expressions for the rate of change of

Use eqn 1.35 to find expressions for the rate of change of the expectation values of position and momentum of a harmonic oscillator; solve the pair of differential equations, and show that the expectation values change i ...

Health insurance market place healthcaregov a project

Health Insurance Market Place (healthcare.gov): A Project Management Perspective The information: Use information from: 1) "From the Start, Signs of Trouble at Health Portal(Which is in the attached PDF file)" and 2) "Ho ...

A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

A simply supported beam of length l is subjected to loads

A simply supported beam of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection at the midpoint of the span. How much strain energy U is stored in the beam if the deflection cu ...

A prototype bolt shaft assume a uniform cylinder that is to

A prototype bolt shaft (assume a uniform cylinder) that is to be loaded in tension is made of a stainless steel with a yield strength of 450 MPa and has a safety factor of 3 with respect to yielding for the maximum allow ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen