Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Describe how transformers are categorized according to their construction?

2) prepare down the emf equation for d.c. generator.

3) Describe why armature core in d.c machines is constructed with laminated steel sheets instead of solid steel sheets?

4) Describe why commutator is used in d.c.machines?

5) prepare down the difference between shunt and series field coil construction.

6) Describe how does d.c. motor differ from d.c. generator in construction?

7) Describe how will you change direction of rotation of d.c.motor?

8) What do you mean by back emf in d.c. motor?

9) Why starter is essential for the dc motor?

10) prepare down the applications of step-up and step-down transformer?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911898

Have any Question? 


Related Questions in Electrical & Electronics

Approximate using a number of terms of your choice through

Approximate (using a number of terms of your choice) through the three forms of Fourier series expansion the periodic signal that is depicted in the following figure Each time, a. Plot the approximate signal in time of t ...

A module with 40 cells has an idealized rectangular i-v

A module with 40 cells has an idealized, rectangular I-V curve with I SC = 4 A and V OC = 20 V. If a single cell has a parallel resistance of 5Ω and negligible series resistance, draw the I-V curve if one cell is complet ...

1 if alice and bob need to communicate using asymmetric-key

1. If Alice and Bob need to communicate using asymmetric-key cryptography, how many keys do they need? Who needs to create these keys? 2. Why do you think asymmetric-key cryptography is used only with small messages. 3. ...

Consider a uniform bar with a cross-sectional area a 2

Consider a uniform bar with a cross-sectional area, A = 2 10 -4  m 2 , and a unit length, L = 1 m. The bar shows elastoplastic material behavior, as depicted in the figure. The plastic deformation starts at yield stress ...

Below is the governing differential equation of

Below is the governing differential equation of one-dimensional bar under uniformly distributed load. Using one bar element, calculate the displacement at x = L and x = 1/2L. Compare these displacements with that of the ...

Consider two bar elements under a force at the tip using

Consider two bar elements under a force at the tip. Using the displacement controlled method, plot the load-displacement curve (F vs. u 2  and u 3 ). Increase the tip displacement u 3  up to 1.0 m by ten equal increments ...

The spacing a between the plates of a parallel-plate

The spacing a between the plates of a parallel-plate waveguide is equal to 5 cm. The dielectric between the plates is free space. If a generator of fundamental frequency 1800 MHz and rich in harmonics excites the wavegui ...

1 how would you characterize a transverse magnetic wave2

1. How would you characterize a transverse magnetic wave? 2. Compare the phenomenon of guiding of uniform plane waves in a parallel-plate waveguide with that in a parallel-plate transmission line.

You are to size a grid-connected south-facing pv system for

You are to size a grid-connected south-facing PV system for Las Vegas to deliver 4000 kWh/yr. Use a tilt equal to latitude minus 15°. a. What should be the ac-rated power of the PV/inverter system? b. What temperature de ...

For the flow described in problem obtain the differential

For the flow described in Problem, obtain the differential equation of motion if v θ  = f(r; t). Problem:- The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a station ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro