Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. What do you mean by robot and robotics.

2. What is meant by work volume?

3. prepare down some joints existing in general robot.

4. Describe when magnetic grippers are preferred.

5. prepare downs the use of sensors in robotics

6. What do you mean by machine vision system?

7. prepare down the various kinds of robot configuration?

8. What do you mean by a robot cell?

9. prepare down the advantages of using robot in material handling.

10. What do you mean by intelligent robots?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912372

Have any Question? 


Related Questions in Mechanical Engineering

A potential flow source having an intensity of 10m2s placed

A potential flow source having an intensity of 10m2/s, placed in the point of Cartesian coordinates (1;0), and a sink having identical intensity, placed in the point (-1;0), are combined with a uniform flow at 25 m/s, in ...

Wat is the resilience of the bolts and joint this time

What is the resilience of the bolts and joint this time? What is the stiffness ratio of this eccentric joint? By how much does the tensile load of 7.40 kips increase the tension in the bolts and reduce the clamping force ...

A compute the intrinsic gate delay of the nmost given in

(a) Compute the intrinsic gate delay of the nMOST given in the above problem and also in section 661 at the biasing condition given above. (b) Compute the intrinsic power-delay product. (c) Does the load resistor increas ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

Fixed-price contracts where the contractor bids a fixed

Fixed-price contracts, where the contractor bids a fixed price to complete a system development, may be used to move project risk from client to contractor. If anything goes wrong, the contractor has to pay. Suggest how ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

1 a 1968 volkswagen sedan is driving over a 7300-ft-high

1. A 1968 Volkswagen sedan is driving over a 7300-ft-high mountain pass at a speed of v m/s into a headwind of W m/s. Compute the gage pressure in mPa at a point on the auto where the velocity relative to the auto is v - ...

Whats the maximum proof strength in ksi of a j429 gr 8 bolt

What's the maximum proof strength (in ksi) of a J429 GR 8 bolt and that of an ASTM A490 bolt? What's the proof strength of a metric Class 10.9 bolt in MPa? What is the ultimate strength and the yield strength (in MPa) of ...

Midterm examinstruction by default the graduate students

Midterm Exam Instruction: By default, the graduate students are required to answer all the question below. Question 1 part a) and Question 5 are not required for undergraduate students but are bonus problem for undergrad ...

There are 3 x 103 spheres in a box calculate the number of

There are 3 x 10 3 spheres in a box. Calculate the number of different combinations for the spheres in order to have 1100 spheres in the front third of the box. Assuming that the distribution is normal, calculate the pro ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro