Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) What do you mean by Proportional controller and prepare down its advantages.

2) prepare down the drawback in P-controller.

3) What do you mean by integral control action?

4) prepare down the advantage and disadvantage in integral controller?

5) What do you mean by PI controller?

6) What do you mean by PD controller?

7) What do you understand by PID controller?

8) What do you understand by time response?

9) What is transient and steady state response?

10) prepare down the importance of test signals?

11) Find out the overall transfer function C(S)/R(S) for system shown in figure:

142_Mechanical system_3.jpg

12) Deduce the transfer function for Armature controlled DC servo motor.

13) Deduce the transfer function for Field controlled DC servo motor.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911016

Have any Question? 


Related Questions in Electrical & Electronics

The section bus-bars a and b are linked by a bus-bar

The section bus-bars A and B are linked by a bus-bar reactor rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA wit ...

A system requires storage for 1 second of video from a

A system requires storage for 1 second of video from a camera. The video data consists of 25 frames per second, with each frame containing 640 × 480 pixels of 24 bits. How much memory is required?

A binary symmetric channel has an error probability of 0005

A binary symmetric channel has an error probability of 0.005. How many of these channels can be cascaded before the overall error probability exceeds 0.1?

For the system in figure 1313 the source voltage is 50 kv

For the system in Figure 13.13, the source voltage is 50 kV (phase value), the feeder reactive reactance X1 is 10Ω and X2 is 5Ω. The load impedance is 3∠20° kΩ. A temporary fault occurs at the location in the figure. The ...

Repeat given problem for the circuit of given figure

Repeat given problem for the circuit of given figure (a). Problem For the circuit of given figure (b): a. Find the total impedance Z T  in polar form. b. Draw the impedance diagram. c. Find the value of C in microfarads ...

In this chapter we learned that a step-down autotransformer

In this chapter, we learned that a step-down autotransformer could be used to reduce the starting current drawn by an induction motor. While this technique works, an autotransformer is relatively expensive. A much less e ...

The capacitor innbspgiven figure is initially charged to 3

The capacitor in given figure is initially charged to 3 V with the polarity shown. a. Find the mathematical expressions for the voltage v C  and the current i C  when the switch is closed. b. Sketch the waveforms for v C ...

Draw the following sheet metal part using cadd software use

Draw the following sheet metal part using CADD software. Use the entry method of your choice. Space is provided in which you can write the coordinate values needed to draw a line to each point-or use a separate sheet.

A 4- microf parallel plate capacitor has 160 microc of

A 4- µF parallel plate capacitor has 160 µC of charge on its plates. If the plates are 5 mm apart, find the electric field strength between the plates.

A lathe is powered by a 50 hp electric motor and is running

A lathe is powered by a 5.0 HP electric motor and is running at 500. RPM. It is turning a 1.0 inch cast iron shaft with a depth of cut of 0.035 in. What is the maximum feed rate that can be used before the lathe stalls?

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

A cola-dispensing machine is set to dispense 9 ounces of

A cola-dispensing machine is set to dispense 9 ounces of cola per cup, with a standard deviation of 1.0 ounce. The manuf

What is marketingbullwhat is marketing think back to your

What is Marketing? • "What is marketing"? Think back to your impressions before you started this class versus how you

Question -your client david smith runs a small it

QUESTION - Your client, David Smith runs a small IT consulting business specialising in computer software and techno

Inspection of a random sample of 22 aircraft showed that 15

Inspection of a random sample of 22 aircraft showed that 15 needed repairs to fix a wiring problem that might compromise

Effective hrmquestionhow can an effective hrm system help

Effective HRM Question How can an effective HRM system help facilitate the achievement of an organization's strate