Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) Describe the 8085 bus structure with a neat sketch.

problem 2) prepare down the peripheral I/O instructions. prepare down its syntax and describe the same with the timing diagram.

problem 3) Describe the 8086 interrupts types in detail.

problem 4) Describe the 8086 bit manipulation instructions with an ex for each.

problem 5) prepare down the 8086 program to convert BCD data to binary data.

problem 6) Describe the 8279 keyboard and sisplay controller with a neat sketch.

problem 7) describe the architecture and working of 8253 timer.

problem 8) Suppose that 5 BCD data items are stored in RAM locations starting at 40H as shown below. prepare an 8051 program to find the sum of all the numbers. The output should be in BCD.

40=(71), 41=(11), 42=(65), 43=(59), 44(37)

problem 9) Describe the working of the 8051 microcontroller. Provide a neat and well labelled sketch.

problem 10) Describe how microcontrollers and microprocessors can be used for the washing machine control application. Use sketches.

problem 11) Describe with a neat and well labelled sketch how microcontrollers and microprocessors can be used for the stepper motor control application.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99017

Have any Question? 


Related Questions in Electrical & Electronics

1 outline the steps involved in the magnetoquasistatic

1. Outline the steps involved in the magnetoquasistatic field analysis of a parallel plate structure and the determination of its input behavior. Compare the input behavior with the magnetostatic case. 2. Outline the ste ...

1 how many points can we have in a dht with m 102 explain

1. How many points can we have in a DHT with m = 10? 2. Explain the problems we encounter if we use IP addresses as the node identifiers in a DHT. 3. Explain two strategies used for storing an object in DHT-based network ...

Question 1a for the circuit shown in figure 1 sketch the

Question 1. (a) For the circuit shown in FIGURE 1 sketch the voltage waveform across the secondary winding of the transformer. On the same diagram sketch the load voltage waveform. The sketches should take into account d ...

Consider a uniform bar with a cross-sectional area a 2

Consider a uniform bar with a cross-sectional area, A = 2 10 -4  m 2 , and a unit length, L = 1 m. The bar shows elastoplastic material behavior, as depicted in the figure. The plastic deformation starts at yield stress ...

1 what is the magnetic flux crossing an infinitesimal

1. What is the magnetic flux crossing an infinitesimal surface oriented parallel to the magnetic flux density vector? 2. For what orientation of the infinitesimal surface relative to the magnetic flux density vector is t ...

1 considering the second hand on your watch to be a vector

1. Considering the second hand on your watch to be a vector, state its polarization. What is the frequency? 2. What is a phasor? 3. Is there any relationship between a phasor and a vector? Explain. 4. Describe the phasor ...

Discretize the continuous-time system with transfer

Discretize the continuous-time system with transfer function H(s) = (s + 10 )/s with use of the bilinear (Tustin) approximation method. Verify your result by converting the computed discrete-time system to continuous-tim ...

The device in the schematic diagram below is a viscosity

The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary case. The case and the drum are concentric. Fluid enters at A, flows through the annulus between the ca ...

The swap operation is one of the components of the modern

The swap operation is one of the components of the modern block ciphers. a. Swap the word (10011011)2. b. Swap the word resulting from part a. c. Compare the results of part a and part b to show that swapping is a selfin ...

An exhaust stream leaving a semiconductor fabrication plant

An exhaust stream leaving a semiconductor fabrication plant contains 4 mol % volatile organic chemical, VOC, pollutant. Twenty-five cubic meters per minute enter the bottom of a packed absorption tower and flows counterc ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen