Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe the procedure by which scheduling two jobs in m machines can be done with appropriate ex.

2) prepare detailed notes on:

a) Aggregate run-out method of batch scheduling.

b) Line of balance method.

3) Describe the concepts, inputs, characteristics, working, outputs, and benefits of MRP in detail.

4) prepare down the functions of dispatching? What are the different documents raised?

5) What do you mean by progressing? Describe its function in detail? Also prepare detailed notes on ‘recording progresses’.

6) prepare down the main cost associated with inventory?

7) List out the types of inventory system and describe them in detail.

8) What do you mean by selective inventory control?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911667

Have any Question? 


Related Questions in Mechanical Engineering

Q1 how did the roman way of waging war contrast with the

Q1. How did the Roman way of waging war contrast with the Greek way? JUST ANSWER THIS QUESTION WITH 150 WORDS ONLY.( NO SOURCES, SIMPLE ANSWER AND VERY SIMPLE ENGLISH SINCE IM AN INTERNATIONAL STUDENT) Q 2. What was acco ...

Asignmentnote all dimensions are in mm unless stated

ASSIGNMENT Note: All dimensions are in mm unless stated otherwise. A steel frame is shown in Figure 1. The steel used is ASTM A572 Grade 50. It consists of two span and braced by an arrangement of trusses at the right si ...

1 explain the read write erase operations of the fmosc

1. Explain the read, write, erase operations of the FMOSC memory cell shown in Fig. 674.4(b). Fig. 674.4 2. Is an initial charge up operation of the FMOSC memory cells necessary immediately after the d.c. power turned on ...

Design design all members of the 6 span truss each span is

Design: Design all members of the 6 span truss each span is 12 ft long, the height of the truss is 16 feet shown if w = 10,000 pounds. The allowable maximum tensile stress P/A is 1000 psi where P is the force in the memb ...

A steel bar of 100mm length tapers from 12mmtimes10mmfrom

A steel bar of 100mm length tapers from 12mm×10mmfrom one end to 30mm×20mm at the other. If the stress in the bar is not to exceed 100mpa,find the magnitude of the axial force. Also find the change in its length. Take E ...

Calculate the total lift force on the arctic hut shown

Calculate the total lift force on the Arctic hut shown below as a function of the location of the opening. The lift force results from the difference between the inside pressure and the outside pressure. Assume potential ...

What is meant by the term prevailing torque what do we

What is meant by the term prevailing torque? What do we mean by the terms initial preload and residual preload? Why do they differ? What limits the usefulness of the so-called, long-form torque-preload equation? Explain ...

1 find the pressure at point a2 using a liquid having a

1. Find the pressure at point A. 2. Using a liquid having a specific gravity of 1.2 and inverting a tube full of this material as shown in the figure, what is the value of h if the vapor pressure of the liquid is 3 psia?

Leaning polea pole of negligible mass leans against a wall

Leaning pole A pole of negligible mass leans against a wall, at angle ? with the horizontal. Gravity is directed down (a) Find the constraint relating the vertical acceleration of one end to the horizontal acceleration o ...

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro