Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

Question 1

The NACA 4412 airfoil has a mean camber line given by

100_Aerodynamics and Flight Mechanics.png

By using thin airfoil theory, calculate

a. Its zero-lift angle of attack.
At the angle of attack of 3o, calculate the followings:

b. Its lift coefficient.

c. The moment coefficient about its quarter-chord point.

d. The location of its center of pressure (xcp/c) and aerodynamic center (xac/c).

The experimental data for NACA 4412 airfoil are given in the Appendix of this Homework set (from Abbott, I.H., von Doenhoff, A.E., and Stivers, Jr., L.S., "Summary of Airfoil Data," NACA Report No. 824, 1945).

e. Compare your results from parts a, b, and c above with the NACA 4412 experimental data and express the percentage difference between your results and experiment.

Question 2

A positively cambered airfoil with a zero-lift angle of attack of -3o has a lift slope of 0.1 per degree.

a. Calculate the lift coefficient at an angle of attack of 5o.

b. Now the same airfoil is turned upside-down (so it becomes an airfoil with a negative camber). Calculate its lift coefficient at the same angle of attack of 5o as in part a.

c. At what angle of attack must the upside-down airfoil be set to generate the same lift as that when it is right-side-up at a 5o angle of attack?

Question 3

A two-dimensional thin wing was tested in a wind tunnel. The pitching moment coefficient about the leading edge (Cm,LE) at zero-lift was found to be -0.02. At angle of attack of 8 deg, Cl = 0.7, Cd = 0.04 and Cm,LE = -0.2. Determine the location of the aerodynamic center of this wing.

Question 4.

Spanwise circulation distribution for a wing of span b in an air flow of density ρ∞ and speed V is parabolic as follows:

684_Aerodynamics and Flight Mechanics1.png

a. Calculate the downwash induced by this circulation at any position y0 along the wing span. Calculate also the downwash at the root of the wing.

b. Find the total lift generated by the wing.

Question 5.

A thin spanwise symmetrical wing has an aspect ratio of 10 and a straight edges with taper ratio (tip chord / root chord) of 0.8 and root chord of 1 m. This wing does not have geometric or aerodynamic twist and it has symmetrical airfoil profile.

a. Compute, using 4 terms in the expansion, the spanwise efficiency factor, e, and plot its drag polar if its zero-lift drag is 0.01.

b. Determine lift coefficient and induced-drag coefficient of the wing at an angle of attack of 4o.

Question 6. The wing of a light, single-engine general aviation aircraft has an area of 15.8 m2 and a span of 9.6 m. The airfoil of the wing is NACA 65-415, which has a lift slope of 0.1033 per degree and zero-lift angle of attack of -3o. Assume the span efficiency factor of 0.893.

a. If the wing is to produce 11 kN lift while cruising at 190 km/h at standard sea level, calculate the geometric angle of attack that the wing should be set to.

b. Calculate also the induced drag experienced by the wing in that condition.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9131059
  • Price:- $50

Priced at Now at $50, Verified Solution

Have any Question?


Related Questions in Mechanical Engineering

Question - truss structureconsider the three membered

Question - Truss Structure Consider the three membered planar truss structure shown in the figure below. All members of the truss have identical square cross-sectional area (A) of 25 mm x 25 mm, and Youngs Modulus (E) = ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Expansion processes of a perfect gasassignment1 attend the

Expansion Processes of a Perfect Gas Assignment: 1. Attend the laboratory class and complete the lab tests according to the supervisor's requirement. Students will not allowed to submit their report if they do not come t ...

1 explain the term critical equipment and provide two clear

1. Explain the term "critical equipment" and provide two clear examples of machinery which falls into this category on board a twin screw motor vessel. 2. Explain the process of Charpy lmpact Testing including sample mar ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

Projectflow processing of liquor in a mineral refining

Project Flow Processing of Liquor in a Mineral Refining Plant The aim of this project is to design a flow processing system of liquor (slurry) in a mineral (aluminum) refining plant. Aluminum is manufactured in two phase ...

The aim of the project is to demonstrate certain aspects of

The aim of the project is to demonstrate certain aspects of engineering materials in different applications. The projects will be assessed on the basis of a written Research Report. The report should clearly show what yo ...

Mechanical engineering assignment task - solve the given

Mechanical Engineering Assignment Task - Solve the given problem. Task 1 - A spring with a one-turn loop of 40mm mean radius is formed from a round section of wire having 5 mm diameter. The straight tangential legs of th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As