Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

Write a research report on load test of an induction motor, in report below points should be included proprly, the repoer should contanins 2000 words. The below given purpose need to be elaborated properly : 

Induction motors are the basic components in today’s electric machinery. So, we started to research on induction motors. Induction motor is a very vast topic. Hence, we decided to research on its load characteristics. We searched methods for determining its load characteristics and chose one method to work becausethe required apparatus for that method was available in our lab. The apparatus consisted of measuring unit, brake control unit, terminal board, three phase induction motor coupled with a generator and a load consisting of electrical bulbs of 200W. That method used a shunt generator but shunt generator was not suitable because of low residual magnetism which gave inappropriate results. Therefore, we switched to separately excited generator which had a separate field supply and had more induced magneto motive force. We gathered data from experiments, analyzed it and plot torque slip curve, output versus efficiency, reactive power versus efficiency, speed versus efficiency, power factor versus efficiency, torque versus efficiency  graphs to see the trends and relationship between them by changing the load. We got better results as compared to the results which were obtained by using shunt generator. So, we recommend separately excited generator.

Your report should cover below points :

List of Tables

  • load test using two wattmeter method of three phase measurement

List of figures

Block Diagram of Setup 

  • Connection diagram
  • Graph between torque and efficiency
  • Graph between power factor and efficiency
  • Graph between speed and efficiency
  • Graph between reactive power and efficiency
  • Graph between output power and efficiency

List of symbols

  • T Torque Developed by the motor
  • Nr Speed of rotor in rpm
  • Ns Synchronous speed in rpm
  • Wr Speed of rotor in radian per second
  • VL Load voltage
  • IL Load current
  • Pout Output power
  • WT Total true three phase power
  • Q Reactive Power
  • cosφ Power Factor
  • η Efficience

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M91828734
  • Price:- $60

Priced at Now at $60, Verified Solution

Have any Question?


Related Questions in Mechanical Engineering

Assignment -q1 explain the difference between the

Assignment - Q1. Explain the difference between the metacentric height of a ship during 'Partially Afloat condition and 'Free Floating' condition; aid a sketch to support your answer. Q2. With the aid of sketches, explai ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

Life cycle assessmentfor your chosen service eg white

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

Fluid mechanics assignment - finite control volume analysis

Fluid Mechanics Assignment - Finite Control Volume Analysis and Dimensional Analysis Q1. The wind blows through a 7ft × 10ft garage door opening with a speed of 5 ft/s as shown in the figure. Determine the average speed, ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

Fluid mechanics assignment - viscous flow in pipesq1 as

Fluid Mechanics Assignment - Viscous Flow in Pipes Q1. As shown in the figure below, water "bubbles up" 3 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-i ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

Heat transfer and combustionyou will need graph paper a

HEAT TRANSFER AND COMBUSTION You will need graph paper, a calculator, a copy of Appendix 1 from lesson HTC - 4 - 2 and access to steam tables to answer this TMA. 1. A fuel gas consists of 75% butane (C 4 H 10 ), 10% prop ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As