+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

This assignment must be produced and presented as a blog on http://www.blogger.com. The student must use their name and course details as the blog title.

• Text size must be equivalent to this document.

Subjects to be covered:

i) Boyles Law
ii) Charles Law

Information can be accessed on the:

•    Internet (Google etc)
•    Library
•    Text books

Assignment requirements:

1) Cover page: including Course details, Student name, Group number
2) Contents page: order of subjects and page numbers information can be found
3) Researched papers on the above laws, showing the students understanding of the laws in their own words, also showing how the laws relate to the internal combustion engine.
4) Reference page: All information must be referenced.
5) Maximum of 500 words per topic.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M9753

Have any Question?

## Related Questions in Mechanical Engineering

### The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

### Whats the maximum proof strength in ksi of a j429 gr 8 bolt

What's the maximum proof strength (in ksi) of a J429 GR 8 bolt and that of an ASTM A490 bolt? What's the proof strength of a metric Class 10.9 bolt in MPa? What is the ultimate strength and the yield strength (in MPa) of ...

### The shear-force diagram for a beam is shown assuming that

The shear-force diagram for a beam is shown. Assuming that only forces (not applied moments) act on the beam, determine the beam's loading and draw the bending moment diagram

### 1 the velocity vector in a two-dimensional flow is given by

1. The velocity vector in a two-dimensional flow is given by the expression v = 10e x  + 7xe y  m/s when x is measured in meters. Determine the component of the velocity that makes a 30° angle with the x axis at the poin ...

### An incompressible fluid flows past a flat plate as in the

An incompressible fluid flows past a flat plate, as in the figure below, with a uniform inlet profile and a polynomial exit profile Compute the volume flow Q across the top surface of the control volume. The plate has wi ...

### It is desired to design a pump-piping system to keep a

It is desired to design a pump-piping system to keep a 1-million-gallon capacity water tank filled. The plan is to use a modified (in size and speed) version of the model A centrifugal pump. Provided is the test data for ...

### Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

### In order to penetrate a workpiece a tungsten carbide drill

In order to penetrate a workpiece, a tungsten carbide drill bit is subject to a torque of 3.8 Nm and an axial force of 5 kN. Tungsten carbide is very strong (compressive strength 1400 MPa, tensile strength 340 MPa) but a ...

### Wat is the resilience of the bolts and joint this time

What is the resilience of the bolts and joint this time? What is the stiffness ratio of this eccentric joint? By how much does the tensile load of 7.40 kips increase the tension in the bolts and reduce the clamping force ...

### Extend the analyses of the three narrow-gate effects to

Extend the analyses of the three narrow-gate effects to include the voltage dependent bulk charge. Give two numerical examples using the submicron transistors of problem P685.5. Problem P685.5 Extend the analyses of the ...

• 4,153,160 Questions Asked
• 13,132 Experts
• 2,558,936 Questions Answered

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro