Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) Describe the functions of vibration absorber.

problem 2) Front axle of a car has pivot centres 1.1 m apart. Length of each steering arm is 150 mm while the track rod is of 1.0 m length. Compute the wheelbase for perfect rolling of the car wheels when inner wheel stub axle is at 55° to the rear centre line.

problem 3) Holzer’s method is the trial and error method used to determine the natural frequency and mode shapes of multimass lumped parameter system for free and forced vibration? Describe in detail.

problem 4) Describe the effect of camber and camber angle in a car.

problem 5) Springs of the automobile trailer are compressed 0.1 m under its own weight. Determine the critical speed when the trailer is passing over a road with a profile of sine wave whose amplitude is 80 mm and the wave length is 14 m. Determine amplitude of vibration at a speed of 60 km/hr.

problem 6) Car whose wheel base is equal to five times the height of its centre of gravity above the ground, is moving on a horizontal road when brakes are applied. If a coefficient of limiting friction between car tyres and rod is 0.5, find out the percentage of weight transferred from the rear to the front axle, on braking.

problem 7) prepare a detailed note on Dunkerby’s lower bound method for finding fundamental frequency.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M99133

Have any Question? 


Related Questions in Mechanical Engineering

If all the states of an ensemble are equally probable then

If all the states of an ensemble are equally probable, then a 0.05 mol sample of an ideal gas at ixed energy in a 1000 cm3 container has a chance of being found in a state where a speciied 1% region of the volume is not ...

1 the pump shown in the figure delivers water at 59degf at

1. The pump shown in the figure delivers water at 59°F at a rate of 550 gal/min. The inlet pipe has an inside diameter of 5.95 in. and it is 10 ft long. The inlet pipe is submerged 6 ft into the water and is vertical. Es ...

The number of molecules crossing a unit area per unit time

The number of molecules crossing a unit area per unit time in one direction is given by where n is the number of molecules per unit volume and v is the average molecular velocity. As the average molecular velocity is app ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

A rigid vessel of volume 0400 m3 containing h2 at 2125degc

A rigid vessel of volume 0.400 m3 containing H2 at 21.25°C and a pressure of 715 X 10 3 Pa is connected to a second rigid vessel of volume 0.750 m 3 containing Ar at 30.15°C at a pressure of 203 X 10 3 Pa. A valve separa ...

The vibrational partition function for an unknown diatomic

The vibrational partition function for an unknown diatomic molecule at 300 K is 2.33. Find the maximum value of the vibrational constant ve in cm-1 such that at least 5% of the molecules in a 300 K sample will be found i ...

On a certain day the barometric pressure at sea level is

On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane in flight indicates a pressure of 10.6 psia, and the temperature gage shows the air temp ...

Task to identify research and present in both written and

Task: To identify, research, and present (in both written and oral formats) a topic in engineering that is currently the focus of ongoing (within the past 5 years) research, investigation, and/or development.The topic mu ...

An aluminum e 70 gpa cantilever must carry an end load of

An aluminum (E = 70 GPa) cantilever must carry an end load of 1.4 kN as shown. However, in this design, when the beam is loaded the end of the cantilever A has to have the same elevation as point C (i.e., the net deflect ...

A solid circular shaft of 40 mm diameter is to be replaced

A solid circular shaft of 40 mm diameter is to be replaced by a hollow circular tube. If the outside diameter of the tube is limited to 60 mm, what must be the thickness of the tube for the same linearly elastic material ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen