Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) Describe the developments in the shape of cars starting from car from Camille Jenatzy in 1899 to the shapes of modern cars. describe the features in terms of fuel efficiency, speed, luxuries etc.

problem 2) describe the motion of the vehicle resisted by Aerodynamic drag, rolling resistance and climbing resistance.

problem 3) describe completely about detail optimization and shape optimization performed as strategies for aerodynamic development of passenger cars.

problem 4) describe the effects of natural wind, wind forces due to steady side winds on aerodynamic stability of a vehicle.

problem 5) Describe the concept of hatch back, fast back and square back for shape optimization of cars.

problem 6) With the help of neat and well labelled diagram, describe the role of a wind tunnel. describe the different construction elements and their working.

problem 7) With the help of neat and well labelled diagram, describe the phenomena of laminar and turbulent boundary layer, their separation and friction drag on a body in two-dimensional flow.

problem 8) What are different types of drag acting on a vehicle. Describe the effect of each type and methods to compute the magnitude of drags.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M99070

Have any Question? 


Related Questions in Mechanical Engineering

A for the system of fig 347 the resistance of each line

a. For the system of Fig. 3.47, the resistance of each line cannot exceed 0.006 Ω, and the maximum current drawn by the load is 110 A. What gage wire should be used? b. Repeat (a) for a maximum resistance of 0.003 Ω, d = ...

Name several factors that can lead to a change in clamping

Name several factors that can lead to a change in clamping force in an assembled joint ? Name at least three sources of bolting standards ? Three different tensile strengths are given for many bolt materials. Name them ? ...

A solid circular rod of known radius is twisted in a

A solid circular rod of known radius is twisted in a testing machine with a known torque T. Only one strain gage is available. Does each of the test setups below give us enough information to determine the shear modulus ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

1 using the expression for the gradient in polar

1. Using the expression for the gradient in polar coordinates (Appendix A), find the gradient of ψ(r,θ) when Where is the gradient maximum? The terms A and a are constant. 2. Given the following expression for the pressu ...

Wind tunnel testing of the concrete reef balls used in

Wind tunnel testing of the concrete reef balls used in artificial reefs is proposed. A typical reef ball (e.g. Figure 1.2) has a diameter of 6 ft, and is immersed in sea water. A scale model is prepared with diameter of ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

1 if the design load is 90 kn 20300 lbf what is the dead

1. If the design load is 90 kN (20,300 lbf), what is the dead load and what is the intensity of the dead load in the light of the live load calculation of Problem CS1.1? 2. Determine the specific weight of lightweight co ...

A dam discharge into a channel of constant width as shown

A dam discharge into a channel of constant width as shown. It is observed that a region of still water backs up behind the jet to a height H. The velocity and height of the flow in the channel are given as v and h, respe ...

If in the system for problem the total drag on the object

If, in the system for Problem, the total drag on the object is measured to be 800 N/m of length normal to the direction of flow, and frictional forces at the walls are neglected, find the pressure difference between inle ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen