Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: With the help of a neat sketch describe the construction and working of different parts of a cathode ray tube.

problem 2: Deduce an expression for the vertical deflection on the screen of a cathode ray tube in terms of length of plates, accelerating voltage, separation distance, deflecting voltage and the distance of screen from the origin.

problem 3: describe the functions of the necessary components of a CRO with the help of block diagram. How the sensitivity of a CR tube is rated? How would you use CRO to measure the phase difference of two sinusoidal signals?

problem 4: Describe with block diagram the different parts of a CRT. What additional components are required to make it a CRO? Describe how you would measure frequency by using a CRO.

problem 5: Describe the different applications of oscilloscope for the measurement of voltage, current, phase angle and frequency.

problem 6: describe how the given are determined from the trace on a CRT.

a) rms value of a sine wave
b) Phase difference between two voltages of the similar frequency.

problem 7: Describe how the applied voltage wave is displayed on the screen of a cathode ray tube. Sketch the similar.

problem 8: What are the different applications of the cathode ray oscilloscope?

problem 9: With the help of a sketch, describe the principle of operation of a cathode ray oscilloscope. Illustrate the applications in the field of measurements.

problem 10: prepare brief notes on the given:

a) Cathode ray oscilloscope.
b) Cathode ray tube.
c) Basic controls of a CRO.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M97583

Have any Question? 


Related Questions in Electrical & Electronics

1 describe the phenomenon of the bouncing back and forth of

1. Describe the phenomenon of the bouncing back and forth of transient waves on a transmission line excited by a constant voltage source in series with internal resistance and terminated by a resistance. 2. Discuss the v ...

1 discuss the input behavior of a short-circuited line for

1. Discuss the input behavior of a short-circuited line for frequencies slightly beyond those for which the quasistatic approximation is valid. 2. What are the boundary conditions for the voltage and current at the junct ...

1 what is the determinant expansion for the curl of a

1. What is the determinant expansion for the curl of a vector? 2. What is the significance of the curl of a vector being equal to zero? 3. State Ampere's circuital law in differential form for the simple case of How is i ...

The power output of a hydraulic turbine depends on the

The power output of a hydraulic turbine depends on the diameter D of the turbine, the density ρ of water, the height H of water surface above the turbine, the gravitational acceleration g, the angular velocity ω of the t ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

Write the expression for the vector distance of a point in

Write the expression for the vector distance of a point in a rectangular room from one corner of the room, choosing the three edges meeting at that point as the coordinate axes. Describe the vector distance field associa ...

A circular loop antenna of radius 1 m in free space carries

A circular loop antenna of radius 1 m in free space carries a uniform current (a) Calculate the amplitude of the electric field intensity at a distance of 10 km in the plane of the loop. (b) Calculate the radiation resis ...

Figure 3013 shows a router using priority queuing at the

Figure 30.13 shows a router using priority queuing at the input port. The arrival and required service times (transmission time is negligible) for 10 packets are shown below; ti means that the packet has arrived i ms aft ...

An ltic system impulse response is given by ht ut-ut - 1a

An LTIC system impulse response is given by h(t) = u(t)-u(t - 1). a. Determine the transfer function H(s). Using H(s), determine and plot the magnitude response |H(jω)|. Which type of filter most accurately describes the ...

1 what is the brewster angle what is the polarization of

1. What is the Brewster angle? What is the polarization of the reflected wave for an elliptically polarized wave incident on a dielectric interface at the Brewster angle? Discuss an application of the Brewster angle effe ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen