Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) With the help of appropriate diagrams and exs, describe external flow and internal flow for a body. Apply Bernoulli’s equation to determine pressure coefficient in terms of velocity and plot CpVs x/l for a vehicle shaped body on upper and lower side.

problem 2) Describe in details about strategies for aerodynamic development of cars in terms of detail optimization, shape optimization and drag reduction methods.

problem 3) Describe in details the optimization analysis of forebody, windshield and roof of a vehicle.

problem 4) Describe the effect of aerodynamic forces on lateral deviation of a vehicle and also expalin the equation for evaluation of the influence of side force, weight and aerodynamic lever arm length.

problem 5) Draw a neat and well labelled sketch of a wind tunnel and describe the functions of various parts.

problem 6) With the help of a neat and well labelled sketch. Describe the procedure to measure aerodynamic forces and moments by wind tunnel balances.

problem 7) describe the origin of forces and moments on a vehicle and discuss the effect of natural and artificial side-wind gusts.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M99074

Have any Question? 


Related Questions in Mechanical Engineering

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

If you were using a full length centerline gage rod to

If you were using a full length, centerline, gage rod to measure DL, how much change would you expect to see at 2508F?  What DL from ‘‘before tightening'' would you expect to see at 2508F if you were using ultrasonics to ...

Confirm that in hydrogenic atoms the spin-orbit coupling

Confirm that in hydrogenic atoms, the spin-orbit coupling constant depends on n and l as in eqn 7.24 2.Calculate the spin-orbit coupling constant for a 2p-electron in a Slater-type atomic orbital, and evaluate it for the ...

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

In problem above find the depth at which the net force on

In Problem above, find the depth at which the net force on the tank is zero. Problem :- On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane ...

Mechanical engineering assignmentproblem - a linearly

Mechanical Engineering Assignment Problem - A linearly increasing load sits on a brass rail of length L. Find the centroid (4) of the cross section below. Using successive integration, find the maximum bending moment (5) ...

Define the endurance limit of a bolt which is greater the

Define the endurance limit of a bolt ? Which is greater, the static yield strength or the endurance limit of the bolt? When will an increase in preload increase fatigue life? When will an increase in preload decrease fat ...

If in the system for problem the total drag on the object

If, in the system for Problem, the total drag on the object is measured to be 800 N/m of length normal to the direction of flow, and frictional forces at the walls are neglected, find the pressure difference between inle ...

If the kansas city building code specified that a floor

If the Kansas City Building Code specified that a floor structure must support a live load of 4.79 kPa (100 psf), and if the walkway length L = 9.1 m = 30.0 ft and width b = 2 m = 6.56 ft, what contribution is made to th ...

A laminated plastic beam with a square cross section is

A laminated plastic beam with a square cross section is built up by gluing together three strips, each 10 mm × 30 mm in cross section. It must carry a load P at its midpoint. a. The beam has a total weight W and a length ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen