Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1)(i) Describe the principle of AJM. prepare down some of the specific applications.

(ii) describe about AJM process variables which influence the rate of material removal and accuracy in the machining in detail.

2)(i) Describe the method of AJM with help of suitable schematic diagram.

(ii) prepare down the advantages and limitations of AJM.

3) Describe the process parameters in WJM processs.

4) With neat and suitable sketch describe the process of AJM. prepare down its application and limitations.

5)(i) Describe the process parameters which influence WJM. prepare down the applications and limitations of WJM

(ii) Briefly describe the application and limitation of WJM in detail.

6) Describe the USM machine setup and describe different feed mechanisms

7)(i) Describe the influence process parameters and applications of USM in detail.

(ii) prepare a detailed note o the different kinds of transducers.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911693

Have any Question? 


Related Questions in Mechanical Engineering

Each wood railroad tie supports part of the weight of a

Each wood railroad tie supports part of the weight of a train (plus the relatively small weight of a section of rail). This is modeled with two point loads representing the force of the rail on the tie. The reaction from ...

1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

1 determine the capillary rise for a water-air-glass

1. Determine the capillary rise for a water-air-glass interface at 40°C in a clean glass tube having a radius of 1 mm. 2. Determine the difference in pressure between the inside and outside of a soap film bubble at 20 °C ...

Now consider a second joint of the same material width and

Now consider a second joint of the same material, width and thickness as the joint in problem 4 above but eccentrically loaded. This time, however, the line of action of the external load is 0.563 in. removed from the ce ...

How do bolt stiffness and joint stiffness affect the angle

How do bolt stiffness and joint stiffness affect the angle of turn versus preload relationship? A rubber washer has been used instead of a metal one, by mistake. How will preload be affected if the same predetermined tor ...

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

A stationary jet engine is shown air with a density of

A stationary jet engine is shown. Air with a density of 0.0805 lb m /ft 3  enters as shown. The inlet and outlet cross-sectional areas are both 10.8 ft 2 . The mass of fuel consumed is 2% of the mass of air entering the ...

A cylindrical pressure vessel of 120 in outside diameter

A cylindrical pressure vessel of 120 in outside diameter, used for processing rubber, is 36 ft long. If the cylindrical portion of the vessel is made from 1 in thick steel (E = 29 × 10 6 psi, ν = 0.25) plate and the vess ...

In order to penetrate a workpiece a tungsten carbide drill

In order to penetrate a workpiece, a tungsten carbide drill bit is subject to a torque of 3.8 Nm and an axial force of 5 kN. Tungsten carbide is very strong (compressive strength 1400 MPa, tensile strength 340 MPa) but a ...

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro