Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1)a) Define the terms Load factor, Demand factor, Capacity factor and use factor.

b) Which type Power plants are more in India? give reasons.

c) List the essential elements of hydro power plant and how the hydro power plants are classified?

2)a) describe with a neat sketch functions of Surge tank.

b) prepare a short note on Mini and Micro Hydro power plant.

c) With a neat sketch describe the working of a Pumped storage Power plant.

3)a) describe different types of fuels used for Power generation.

b) describe with a neat sketch working of a Spreader stoker firing system.

c) What is the difference between Unit and Central bin pulverizing system?

4)a) What are the advantages of using High pressure boilers?

b) With a neat sketch describe characteristics of a Benson Boiler.

c) describe in brief Natural, Forced and Balanced draught of Chimney.

5)a) Why cooling and Lubrication system is required for a Diesel power plants?

b) What are the advantages of Open cycle gas power plants?

c) Draw and describe Elements of Nuclear Reactor.

6)a) With a neat sketch describe the characteristics and its advantages of BWR.

b) describe with a neat sketch Characteristics of Fast Breeder reactor.

c) prepare a short note on Waste Disposal method.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M94469

Have any Question? 


Related Questions in Mechanical Engineering

1 the pump shown in the figure delivers water at 59degf at

1. The pump shown in the figure delivers water at 59°F at a rate of 550 gal/min. The inlet pipe has an inside diameter of 5.95 in. and it is 10 ft long. The inlet pipe is submerged 6 ft into the water and is vertical. Es ...

A laminated plastic beam with a square cross section is

A laminated plastic beam with a square cross section is built up by gluing together three strips, each 10 mm × 30 mm in cross section. It must carry a load P at its midpoint. a. The beam has a total weight W and a length ...

Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

It has been observed that the most effective way to crush

It has been observed that the most effective way to crush an empty aluminum beverage can is to apply an eccentric compressive load. Use buckling theory to explain this phenomenon. The can wall thickness is 80 μm, and the ...

A critical bolted joint in a nuclear power plant requires a

A critical bolted joint in a nuclear power plant requires a specific bolt preload. The access prevents a direct, accurate measurement of the actual bolt preload. It is planned to use a UNF 7/16-20 bolt with a root diamet ...

In a small generating system there are two generators in

In a small generating system, there are two generators in parallel. One of them is a synchronous generator, and the other, an IG. The common load is 3.0 kW with a power factor of 0.92. If the IG supplies only 1.0 kW of t ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

A rigid vessel of volume 0400 m3 containing h2 at 2125degc

A rigid vessel of volume 0.400 m3 containing H2 at 21.25°C and a pressure of 715 X 10 3 Pa is connected to a second rigid vessel of volume 0.750 m 3 containing Ar at 30.15°C at a pressure of 203 X 10 3 Pa. A valve separa ...

1 draw the moment diagram for the elbow-biceps-forearm-hand

1. Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment. 2. How do the magnitudes of the biceps force B and joint reaction J change if the total ...

Water in an open cylindrical tank 15 ft in diameter

Water in an open cylindrical tank 15 ft in diameter discharges into the atmosphere through a nozzle 2 in. in diameter. Neglecting friction and the unsteadiness of the flow, find the time required for the water in the tan ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen