Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1)i) prepare down the features of CAN (Controller  Area Network) Module in detail.

(ii) Describe the DSP controllers TMS320LF2407 and TMS320LF2812 in detail.

2) With a neat and suitable block diagram, describe the operation of Serial Peripheral Interface (SPI) in master mode and slave mode in detail.

3)a) With a neat and suitable functional block diagram of TMS320C24x DSP Controller, describe the function of each block in detail.

4)(i) With a neat and suitable block diagram, describe the operation of Central Arithmetic Logic unit/section present in CPU of TMS320C24x.

(ii) prepare about immediate addressing mode with suitable ex.

5)a) describe the operation and number of cycles needed to perform the instructions given below.

(i) ABS   

(ii) ADDC dma   

(iii) OR dma

(iv) PAC

(v) POP.

6) Show the function of branch instructions and control instructions with at least five suitable instructions exs in each category.

7) With a neat and suitable functional block diagram of event manager module, describe the operation of each blocks.

8)(i) Sketch and describe the block diagram of PWM circuits related with compare units.

(ii) prepare brief notes on Event Manager Interrupts and describe how are they serviced?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M912563

Have any Question? 


Related Questions in Electrical & Electronics

1 list the components of a traffic conditioner in diffserv2

1. List the components of a traffic conditioner in DiffServ. 2. Is the flow label in IPv6 more appropriate for IntServ or DiffServ?

1 discuss with the aid of an example the discharging of an

1. Discuss with the aid of an example the discharging of an initially charged line into a resistor. 2. Discuss the bounce-diagram technique of transient analysis of a line with uniform initial voltage and current distrib ...

Answer the following questionsa how many output lines would

Answer the following questions. a. How many output lines would a 4 input decoder have? b. How many output lines would a 5 input decoder have? c. For an N-to-X decoder, specify X as a function of N (e.g. specify the numbe ...

1 in internet telephony explain how a call from alice can

1. In Internet telephony, explain how a call from Alice can be directed to Bob when he could be either in his office or at home? 2. Do you think H.323 is actually the same as SIP? What are the differences? Make a compari ...

In problem find the rate of discharge if the frictional

In Problem , find the rate of discharge if the frictional head loss in the pipe is 3.2 v2 /g where v is the flow velocity in the pipe. Problem:- Referring to the figure, assume the flow to be frictionless in the siphon. ...

The exponential fourier spectra of a certain periodic

The exponential Fourier spectra of a certain periodic signal x(t) are shown in Fig. 6.13. Determine and sketch the trigonometric Fourier spectra of x(t) by inspection of Fig. 6.13. Now write the (compact) trigonometric F ...

Compute and plot the solution of the difference equation yn

Compute and plot the solution of the difference equation y[n] þ y[n 1] = 2x[n] þ x[n 1], where x[n] = 0.8n u[n] assuming zero initial conditions. Moreover, verify your answer (a) by examining if the derived solution sati ...

1 we discuss the use of sip in this chapter for audio is

1. We discuss the use of SIP in this chapter for audio. Is there any drawback to prevent using it for video? 2. Assume two parties need to establish IP telephony using the service of RTP. How can they define the two ephe ...

The strain energy and work done by applied loads are given

The strain energy and work done by applied loads are given in the following equations. When the solution is expressed by u(x) = c 1 x + c 2 x 2 , calculate the solution using the principle of minimum potential energy.

A voltage source vt 100 cos2pi50 t v is applied to a

A voltage source v(t) = 100 cos(2π50 t) [V] is applied to a nonlinear load, resulting in non-sinusoidal current: i(t) = 4 + 10 cos(2π50 t +30°) + 20 cos (4π50 t +45°) [A]. Determine: (a) the power absorbed on the load, ( ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro