Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Describe the term Frequency agility.

problem 2: Illustrate that the product of the maximum unambiguous range and the first blind speed v1 is equivalent to c/4.

problem 3: Find out the highest frequency on which radar can be operated if it is needed to have a maximum unambiguous range of 200 NMI and no blind speeds less than 600 Km.

problem 4: Show that a triple delay line canceller is equal to a four pulse delay line canceller with weights equivalent to the coefficients of the binomial expansion with alternating signs.

problem 5: Why does a high PRF pulse Doppler radar need a much larger improvement factor than low PRF MTI radar, supposing comparable performance in detecting moving targets in clutter?

problem 6: Why can’t the altitude line in a high PRF pulse Doppler radar be removed by range gating instead of by filtering?

problem 7: VHF radar at 220 MHz has a maximum unambiguous range of 180 nmi.

a) Determine its first blind speed?
b) Repeat for an L band radar at 1250 MHz.

problem 8: What does a medium PRF pulse Doppler radar do better than the high PRF pulse Doppler radar?

problem 9: What does high prf radar do better than the medium prf pulse Doppler radar?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M97524
  • Price:- $50

Guranteed 36 Hours Delivery, In Price:- $50

Have any Question? 


Related Questions in Electrical & Electronics

1 briefly outline the procedure involved in the successive

1. Briefly outline the procedure involved in the successive solution of Maxwell's equations. 2. How does the technique of successive solution of Maxwell's equations reveal the interaction between the electric and magneti ...

Tasks1learn how to use opendss2open and execute the epri

Tasks 1. Learn how to use OpenDSS 2. Open and execute the EPRI Test Circuit 24 model 3. Develop base case data sets of bus voltages and power flows 4. Provide analysis of the base case model: a. Feeder voltage profiles b ...

1 show the outline of a routing table for pastry with

1. Show the outline of a routing table for Pastry with address space of 16 and b = 2. Give some possible entries for each cell in the routing table of Node N21. 2. In a Pastry network using DHT, in which m = 4 and b = 2, ...

1 implement the 2-to-4 decoder using 7404 not an 7808 and

1. Implement the 2-to-4 decoder using 7404 (NOT) an 7808 (AND) chips on your breadboard. 2. Implement the 2-to-4 decoder circuit with a 74139 chip on your breadboard. 3. Implement a 1-to-2 decoder in Logisim. Implement t ...

1 prove that a signal cannot be simultaneously timelimited

1. Prove that a signal cannot be simultaneously timelimited and bandlimited. 2. The signal x(t) = sin(0.7πt) cos(0.5πt) is sampled using Fs = 1 Hz to yield a discretetime signal x[n]. Next, x[n] is filtered using an idea ...

1 the tank is accelerated upward at a uniform rate does the

1. The tank is accelerated upward at a uniform rate. Does the manometer level go up or down? 2. Glass viewing windows are to be installed in an aquarium. Each window is to be 0.6 m in diameter and to be centered 2 m belo ...

Consider a uniform bar with a cross-sectional area a 2

Consider a uniform bar with a cross-sectional area, A = 2 10 -4  m 2 , and a unit length, L = 1 m. The bar shows elastoplastic material behavior, as depicted in the figure. The plastic deformation starts at yield stress ...

A liquid of density rho flows through a sluice gate as

A liquid of density ρ flows through a sluice gate as shown. The upstream and downstream flows are uniform and parallel, so that the pressure variations at stations 1 and 2 may be considered hydrostatic. (a) Determine the ...

A number equal to the sum of its coordinates is assigned to

A number equal to the sum of its coordinates is assigned to each point in a rectangular room having three of its contiguous edges as the coordinate axes. Draw a sketch of the constant-magnitude surfaces for the number fi ...

The spacing a between the plates of a parallel-plate

The spacing a between the plates of a parallel-plate waveguide is equal to 5 cm. The dielectric between the plates is free space. If a generator of fundamental frequency 1800 MHz and rich in harmonics excites the wavegui ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro