Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1. Transform Hex BSC to binary.

2. Perform the following operation: Add binary numbers: 1101 + 1001 + 1111.

3. Transform decimal 100. 5 to binary.

4. What do you understand by minterm and maxterm?

5. prepare De-Morgans theorem. describe it in suitable ex.

6. Design the symbol of a 4 input NAND gate and 3-input X-OR.

7. What is the funcion of a half adder and half subtractor?

8. What do you understand by combinational circuits? Give suitable exs.

9. Where do we utilize MUX and DEMUX?

10. prepare the truth table of half adder and draw its circuit.

11. What are the different kinds of Flip Flop?

12. Where do we use Flip Flop and memories?

13. How Register constitute a memory?

14. Describe what do you understand by Main and Secondary memories.

15. Where do we utilize D-Flip Flop and clocked Flip Flops?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99467

Have any Question? 


Related Questions in Electrical & Electronics

1 how would you characterize a transverse magnetic wave2

1. How would you characterize a transverse magnetic wave? 2. Compare the phenomenon of guiding of uniform plane waves in a parallel-plate waveguide with that in a parallel-plate transmission line.

1 what is a radiation pattern2 discuss the radiation

1. What is a radiation pattern? 2. Discuss the radiation pattern for the power density due to the Hertzian dipole. 3. Define the directivity of an antenna. What is the directivity of a Hertzian dipole?

Determine the head loss between stations 1 and 2 in

Determine the head loss between stations (1) and (2) in Problem. Problem:- Oil (sp. gr. = 0.8) flows smoothly through the circular reducing section shown at 3 ft 3  /s. If the entering and leaving velocity profiles are u ...

A square block of surface area a on all sides is under pure

A square block of surface area A on all sides is under pure shear deformation due to the uniformly distributed load F on the top surface, as shown in the figure. The deformation of the block is such that the deformed coo ...

1 in a chord network we have node n5 and key k5 is n5 the

1. In a Chord network, we have node N5 and key k5. Is N5 the predecessor of k5? Is N5 the successor of k5? 2. In a Kademlia network, the size of the identifier space is 1024. What is the height of the binary tree (the di ...

1 in kademlia assume m 4 and active nodes are n4 n7 and

1. In Kademlia, assume m = 4 and active nodes are N4, N7, and N12. Where is the key k3 stored in this system? 2. In Chord, assume the size of the identifier space is 16. The active nodes are N3, N6, N8, and N12. Show the ...

1 in internet telephony explain how a call from alice can

1. In Internet telephony, explain how a call from Alice can be directed to Bob when he could be either in his office or at home? 2. Do you think H.323 is actually the same as SIP? What are the differences? Make a compari ...

Consider a plane-strain square element with unit depth as

Consider a plane-strain square element with unit depth as shown in the figure. Use the St. Venant-Kirchhoff isotropic material model with two Lame's constants λ and μ. A uniformly distributed force T x  (force per area) ...

For an ltid system specified by the equationa find the

For an LTID system specified by the equation a. Find the amplitude and the phase response. b. Find the system response y[n] for the input x[n] = cos (0.5k - (π/3)).

Determine if the filters with the following transfer

Determine if the filters with the following transfer functions are physically realizable. If they are not realizable, explain if and how they can be approximately realized. Be as specific as possible. (c) H(ω)=2πδ(ω)

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen