Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem:

A) Steam at 5.0 MPa, 500 degrees C enters an insulated turbine operating at steady state with a mass flow rate of 7kg/s and exits at 0.3 MPa. The Kinetic and potential energy effects are negligible.  Find out the maximum theoretical power which can be developed by the turbine, in kW, and the corresponding exit temperature. Whenever the steam exit the turbine at 250 degrees C, and 0.5 MPa, find out the isentropic efficiency.

B) The Novel Air Conditioning Company claims to have developed a new air conditioner that will maintain a room at 22 degrees C while refusing 105kJ of heat at 42 degrees C. The unit needs 10kJ or work.  Is this device authentic? Why?

C) The reversed Carnot engine as a heat pump consumes 6 kW and has a COP of 3.0. A house, having 1800 kg of air, is initially at 12 degrees C and the heat increases the air temperature to 21 degrees C. How long will this take?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M997

Have any Question? 


Related Questions in Mechanical Engineering

Hydraulic circuit pressure dropthe hydraulic circuit shown

Hydraulic Circuit Pressure Drop The hydraulic circuit shown involves a pump and four pressure restrictions. Assuming the reservoir is at atmospheric pressure and the flow is at steady-state, determine the gage pressures ...

Bull why do individual bolts relax a bit when first

• Why do individual bolts relax a bit when first tightened? Name several factors that can increase the relaxation ? Which will tend to loose more preload after initial tightening, a short bolt or a long bolt? • What are ...

The stepped shaft rotates at 120 rpm and has a 20 kw input

The stepped shaft rotates at 120 rpm and has a 20 kW input at A. 16 kW is taken off to operate machinery at B, and the remaining 4 kW is used at C. The shaft is stainless steel with yield strength in shear of 300 MPa. a. ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

There are 3 x 103 spheres in a box calculate the number of

There are 3 x 10 3 spheres in a box. Calculate the number of different combinations for the spheres in order to have 1100 spheres in the front third of the box. Assuming that the distribution is normal, calculate the pro ...

Introductionemployers are constantly asking for engineering

Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers need to be creative and innovative. They have to ...

Determine the tip deflection of a beam with linear varying

Determine the tip deflection of a beam with linear varying width b(x), constant height h, length L, and elastic modulus E due to tip load P. Write the answer in terms of the maximum width b L = b(L). Also determine the n ...

Experiment title heat engine experimentacademic in charge

Experiment title: Heat Engine Experiment Academic in charge of experiment: Experiment duration: The standard scheduled time for this experiment is 90 minutes for 3 groups (A, B, C) of 6 students. Each group undertakes ex ...

1 a differential manometer is used to measure the pressure

1. A differential manometer is used to measure the pressure change caused by a flow constriction in a piping system as shown. Determine the pressure difference between points A and B in psi. Which section has the higher ...

A critical bolted joint in a nuclear power plant requires a

A critical bolted joint in a nuclear power plant requires a specific bolt preload. The access prevents a direct, accurate measurement of the actual bolt preload. It is planned to use a UNF 7/16-20 bolt with a root diamet ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen