Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) What do you understand by automation?

problem 2) What is direction control valve?

problem 3) What is the objective of vibratory bowl feeder?

problem 4) What do you understand by transducer?

problem 5) prepare down the advantages of programmable logic controllers.

problem 6) What do you understand by fluidics?

problem 7) What do you understand by tactile sensor?

problem 8) prepare down the advantages of welding robot.

problem 9) How will you define robot work volume?

problem 10) Briefly describe robot vision system.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98898

Have any Question? 


Related Questions in Mechanical Engineering

The illustration below shows a vane with a turning angle

The illustration below shows a vane with a turning angle θ which moves with a steady speed v c . The vane receives a jet that leaves a fixed nozzle with speed θ. (a) Assume that the vane is mounted on rails as shown in t ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

1 consider the differential control volume shown below by

1. Consider the differential control volume shown below. By applying the conservation of mass and the momentum theorem, show that dP + pvdv + g dy = 0 2. Water flows steadily through the horizontal 30° pipe bend shown be ...

1 according to rfc 1939 a pop3 session is in one of the

1. According to RFC 1939, a POP3 session is in one of the following four states: closed, authorization, transaction, or update. Draw a diagram to show these four states and how POP3 moves between them. 2. POP3 protocol h ...

1 a cylindrical pressure vessel with hemispherical endcaps

1. A cylindrical pressure vessel with hemispherical endcaps has radius r = 2 m, wall thickness t = 10 mm, and is made of steel with yield stress σy = 1800 MPa. It is internally pressurized at p = 2 MPa. Compare the Tresc ...

Calculate the pressure in bar that would be equivalent to

Calculate the pressure in bar that would be equivalent to the attractive force between the Na + and Cl - ions in a salt crystal, at a separation of 2.81 Å and approximating the area over which the force works to be 4.00A ...

Two structural steel shafts with flanges forged on their

Two structural steel shafts with flanges forged on their ends are rigidly connected with a circle of bolts. The shafts are meant to rotate in their supports at A and D, however a 100 N · m torque is applied to flange B w ...

1 estimate the viscosity of nitrogen at 175 k using given

1. Estimate the viscosity of nitrogen at 175 K using given equation. 2. Calculate the viscosity of oxygen at 350°K and compare with the value given in Appendix I. 3. What is the percentage change in the viscosity of wate ...

A sample of he ions is prepared at a temperature of 298 k

A sample of He + ions is prepared at a temperature of 298 K and a density of 2.0 # 10 10 cm -3 . Because these are ions, magnetic ields may be used to trap those ions with kinetic energy less than some threshold value et ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen