Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Q1. What is the characteristic of the system matrix of a FEA analysis? Which information can you extract from the pivot ratio?

Q2. Through three reasons discuss the possible errors occurred by un-correct loading.

Q3. Give three reasons for which non-linear FEA is required when not expected.

Q4. Which tools does Ansys propose to estimate errors? Give brief explanation and provide the command line for the three of them?

Q5. Discuss linear and parabolic elements within their application. Which one of linear or parabolic elements would you use for highly curved geometries? describe why.

Q6. What is a discretisation error? What is a formulation error? What is a numerical error?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912324

Have any Question? 


Related Questions in Mechanical Engineering

Why do we often want to create the correct preload in the

Why do we often want to create the correct preload in the bolts when we assemble a joint? Under what conditions is correct preload relatively unimportant? Name at least three factors that can increase the stress in previ ...

Airplane fuselages are subject to a variety of complex

Airplane fuselages are subject to a variety of complex loads during flight. Consider a Boeing 777 modeled as a cylinder with 1/4 in wall thickness of 2024 aluminum, 209 ft length and 20.3 ft outer diameter. Assume the cy ...

1 according to the equipartition principle what is the

1. According to the equipartition principle, what is the overall energy in J of one mole of water at 1000 K if translational, rotational, and vibrational degrees of freedom are considered? 2. How many equipartition degre ...

An i-beam with the proportions shown is to be used as a

An I-beam with the proportions shown is to be used as a long column. There is a concern about buckling, so two reinforcing plates are to be welded along the length of the column. Two options for the resulting cross secti ...

1 explain the difference between rotor speed and rotor

1. Explain the difference between rotor speed and rotor frequency. For s = -0.01 and a rotor speed of 1740 rpm, what is the rotor frequency for a 60 Hz induction generator? 2. Explain why the efficiency of an induction g ...

Determine the effective moment and vertical shear force

Determine the effective moment and vertical shear force that would be required to replicate the effect of the three bar forces in Problem 1.15. Problem 1.15: For the truss shown, find the bar forces at the section indica ...

1 draw the moment diagram for the elbow-biceps-forearm-hand

1. Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment. 2. How do the magnitudes of the biceps force B and joint reaction J change if the total ...

1 according to rfc 1939 a pop3 session is in one of the

1. According to RFC 1939, a POP3 session is in one of the following four states: closed, authorization, transaction, or update. Draw a diagram to show these four states and how POP3 moves between them. 2. POP3 protocol h ...

The space between two very long parallel plates separated

The space between two very long parallel plates separated by a distance h is filled with a fluid with viscosity where μ0 is a constant and n is a constant exponent. The top plate slides to the right with a constant speed ...

1 a glass bulb of volume 0198 l contains 0457 g of gas at

1. A glass bulb of volume 0.198 L contains 0.457 g of gas at 759.0 Torr and 134.0°C. What is the molar mass of the gas? 2. A 455 cm 3 vessel contains a mixture of Ar and Xe. If the mass of the gas mixture is 2.245 g at 2 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen