Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. What do you mean by electrical discharge machining?

2. prepare down the functions of dielectric fluid used in EDM. Describe them in detail.

3. What is the basic requirement of dielectric fluid used in EDM?

4. What the dielectric fluids usually used in EDM?

5. prepare down the name of some of the tool material used in EDM.

6. Describe the process parameter efficiency the MRR.

7. Describe electrode wear in detail.

8. prepare down the kinds of power supply circuits used in EDM?

9. What are the design factors that are to be considered during selecting the machine tool?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911694

Have any Question? 


Related Questions in Mechanical Engineering

1 calculate and confirm the maximum bending stress of the

1. Calculate and confirm the maximum bending stress of the stainless steel nail plate given above. 2. Research and identify the major materials compatibility issues that arise when devices such as the nail plate are inse ...

Salt water containing 192 lbgal of salt flows at a fixed

Salt water containing 1.92 lb/gal of salt flows at a fixed rate of 2 gal/min into a 100-gal tank, initially filled with fresh water. The density of the incoming solution is 71.8 lb/ft 3 . The solution, kept uniform by st ...

The wrong size bolts were used to connect the flanges in

The wrong size bolts were used to connect the flanges in Problem 5.8, and when the torque is applied to flange B it rotates by 2 degrees (twisting shaft AB) before engaging flange C. Once flange C is engaged both B and C ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

Hypochlorite ion used as the chlorinating agent in swimming

Hypochlorite ion, used as the chlorinating agent in swimming pools, can decompose exothermically, in rare occasions even causing ires. he principal decomposition mechanism is believed to be a. Find the steady-state conce ...

Problem 1 -there is a circular combined open and closed

Problem 1 - There is a circular combined open and closed thin-walled section as shown in the figure. (R = 100mm, t = 2mm, S y = 100N) When shear force S y is applied to Web 24, calculate: a) Calculate I xx for the x-axis ...

A simply supported beam of length l is subjected to loads

A simply supported beam of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection at the midpoint of the span. How much strain energy U is stored in the beam if the deflection cu ...

An air conditioner is a refrigerator with the inside of the

An air conditioner is a refrigerator with the inside of the house acting as the cold reservoir and the outside atmosphere acting as the hot reservoir. Assume that an air conditioner consumes 1.70 X 10 3 W of electrical p ...

16smce310 16scve310 - engineering skills project brief

16SMCE310 / 16SCVE310 - Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On to ...

A bar consists of two portions bc and c d of the same

A bar consists of two portions BC and C D of the same material and of the same length L, but of different cross sections. Determine the strain energy of the bar when it is subjected to an axial load P, expressing the res ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro