Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. What is requirement for unconventional machining processes?

2. Describe how non-traditional machining processes are categorized?

3. prepare down the requirement which demands the use of advanced machining process.

4. Describe why unconventional mechanical machining process is not so effective on soft metals like aluminium?

5.(i) Describe the factors which must be considered in the selection of the suitable unconventional machining process for a given job.

(ii) Compare and contrast different unconventional machining process on basis of type of energy employed, material removal rate, transfer media and economical aspects.

6. prepare down the advantages of AJM process.

7. prepare down the applications of AJM.

8. prepare the Disadvantages of AJM process?

9. describe the abrasive of their application for various operation?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911690

Have any Question? 


Related Questions in Mechanical Engineering

For a deck supports of length 325 m are proposed to be

For a deck, supports of length 3.25 m are proposed to be built from aluminum with a Young's modulus of 72 GPa and a yield stress of 480 MPa. A cylindrical design is proposed with outer diameter d = 100 mm and wall thickn ...

The figure illustrates the operation of an air lift pump

The figure illustrates the operation of an air lift pump. Compressed air is forced into a perforated chamber to mix with the water so that the specific gravity of the air-water mixture above the air inlet is 0.5. Neglect ...

On a certain day the barometric pressure at sea level is

On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane in flight indicates a pressure of 10.6 psia, and the temperature gage shows the air temp ...

1 if the design load is 90 kn 20300 lbf what is the dead

1. If the design load is 90 kN (20,300 lbf), what is the dead load and what is the intensity of the dead load in the light of the live load calculation of Problem CS1.1? 2. Determine the specific weight of lightweight co ...

The probability of a linear molecule being in a particular

The probability of a linear molecule being in a particular rotational level J depends on the temperature, and for J 7 0 there is a temperature Tmax at which the probability for that level reaches a maximum. Derive an exp ...

You have been introduced to a number of different tools

You have been introduced to a number of different tools that can be used to help IE's and MfgE's analyze and develop solutions to make processes more effective and efficient. Watch the video located at http://www.iienet2 ...

Projectdesign a tube bank that will increase the

Project Design a tube bank that will increase the temperature of a 1200 CFM flow of air from 35°F to 100°F. Assume a constant pressure of 1atm. Each tube will have a diameter of 0.5in and a length of 24in. The tube confi ...

1 explain the difference between rotor speed and rotor

1. Explain the difference between rotor speed and rotor frequency. For s = -0.01 and a rotor speed of 1740 rpm, what is the rotor frequency for a 60 Hz induction generator? 2. Explain why the efficiency of an induction g ...

A w10 times 45 beam is made of structural steel and used as

A W10 × 45 beam is made of structural steel and used as a column with a length 15 ft. If its ends are fixed, can the column support the critical load without yielding? (Thedesignation W10 × 45 provides specifications abo ...

Two small cubes of equal size but made of different

Two small cubes of equal size but made of different materials are stacked (as shown in the figure below), so they just fit between two rigid surfaces. The bottom cube is subjected to a uniform pressure p on each of its e ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro