Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) What is the requirement for ALE signal in 8085 microprocessor?

2) How many machine cycles are required to execute STA 1800?

3) What is the requirement for interfacing?

4) prepare down the difference between memory mapped I/O and peripheral mapped I/O.

5) What do you mean by memory mapping?

6) What are the different addressing modes of 8085

7) What do you mean by Hardware interrupts?

8) What do you mean by Software interrupts,

9) What do you understand by interrupt? describe it in detail

10) What do you understand by vectored and non vectored interrupts?

11) What is the requirement for timing diagram?

12) describe in detail the following terms:

i) Instruction cycle

ii) Machine cycle

13) Describe T-state and in which T-cycle the ALE signal is activated?

14) What do you mean by masking and why it is required?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99222

Have any Question? 


Related Questions in Electrical & Electronics

Clculate the surface integral of the vector function f

Calculate the surface integral of the vector function, F = xe 1  + ye 2 , over the portion of the surface of the unit sphere, S : x 2  + y 2  + z 2  = 1, above the xy-plane, i.e., z > 0.

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

The strain energy and work done by applied loads are given

The strain energy and work done by applied loads are given in the following equations. When the solution is expressed by u(x) = c 1 x + c 2 x 2 , calculate the solution using the principle of minimum potential energy.

In digital communication systems transmission of digital

In digital communication systems, transmission of digital data is encoded using bandlimited pulses in order to utilize the channel bandwidth efficiently. Unfortunately, bandlimited pulses are nontimelimited; they have in ...

The single-phase full-bridge inverter from fig 62a has a

The single-phase full-bridge inverter from Fig. 6.2a has a square-wave voltage across a series R-L load. The switching frequency is 50 Hz, the DC input voltage is 250 V, and the load is a serial connection of R = 10 Ω an ...

1 for flow at very low speeds and with large viscosity the

1. For flow at very low speeds and with large viscosity (the so-called creeping flows) such as occur in lubrication, it is possible to delete the inertia terms, Dv/Dt, from the Navier- Stokes equation. For flows at high ...

Projecta cyclolron is an electrically - powered device that

Project A cyclolron is an electrically - powered device that is used to accelerate particles, specifically using both Electrostatic fields and Magneto static fields to accelerate charged particles outwards from a center ...

1 how do you find the approximate value of the surface

1. How do you find the approximate value of the surface integral over a given surface? 2. How do you find the exact value of the surface integral? 3. Provide physical interpretations for the closed surface integrals of a ...

A the highest frequency in the spectrum x omega fig p81-8a

a. The highest frequency in the spectrum X (ω) (Fig. P8.1-8a) of a bandpass signal x (t) is 30 Hz. Hence, the minimum sampling frequency needed to sample x (t) is 60 Hz. Show the spectrum of the signal sampled at a rate ...

1 briefly outline the procedure involved in the successive

1. Briefly outline the procedure involved in the successive solution of Maxwell's equations. 2. How does the technique of successive solution of Maxwell's equations reveal the interaction between the electric and magneti ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro