Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) prepare down the operation modes of 8255.

2) describe the purpose of control word written to control register in 8255?

3) What is the size of ports in 8255?

4) What do you mean by memory mapping and I/O mapping?

5) What do you mean by an USART?

6) describe the use of 8251 chip?

7) prepare down the major components of the keyboard/Display interface.

8) What do you mean by Key bouncing?

9) describe the use of stepper motor?

10) Design the status word format for 8254.

11) What do you mean by key bouncing?

12) prepare the function of crossbar switch?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910962

Have any Question? 


Related Questions in Electrical & Electronics

1 explain the term internal inductance2 what is meant by

1. Explain the term internal inductance. 2. What is meant by the quasistatic extension of the static field in a physical structure? 3. Outline the steps involved in the electroquasistatic field analysis of a parallel pla ...

A number equal to the sum of its coordinates is assigned to

A number equal to the sum of its coordinates is assigned to each point in a rectangular room having three of its contiguous edges as the coordinate axes. Draw a sketch of the constant-magnitude surfaces for the number fi ...

The swap operation is one of the components of the modern

The swap operation is one of the components of the modern block ciphers. a. Swap the word (10011011)2. b. Swap the word resulting from part a. c. Compare the results of part a and part b to show that swapping is a selfin ...

Figure 3012 shows a router using fifo queuing at the input

Figure 30.12 shows a router using FIFO queuing at the input port. The arrival and required service times for seven packets are shown below; ti means that the packet has arrived or departed i ms after a reference time. Th ...

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

A signal is bandlimited to 12 khz the band between 9 and 12

A signal is bandlimited to 12 kHz. The band between 9 and 12 kHz has been corrupted by excessive noise to the point that the information within this band is nonrecoverable. Determine the minimum sampling rate for this si ...

1 what is the direction of the magnetic field for a uniform

1. What is the direction of the magnetic field for a uniform plane wave having its electric field in the positive z-direction and propagating in the positive x-direction? 2. What is intrinsic impedance? What is its value ...

Suppose that a discrete-time system is described by the

Suppose that a discrete-time system is described by the frequency response Find the frequency response of an equivalent system whose frequency response has five terms of ejv in the numerator and six terms of ejv in the d ...

1 a 0635-cm hydraulic line suddenly ruptures 8 m from a

1. A 0.635-cm hydraulic line suddenly ruptures 8 m from a reservoir with a gage pressure of 207 kPa. Compare the laminar and inviscid flow rates from the ruptured line in cubic meters per second. 2. A common type of visc ...

1 a 16-scale model of a torpedo is tested in a water tunnel

1. A 1/6-scale model of a torpedo is tested in a water tunnel to determine drag characteristics. What model velocity corresponds to a torpedo velocity of 20 knots? If the model resistance is 10 lb, what is the prototype ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro