Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) describe the socio economic consideration of Industrial Automation?

problem 2) What do you mean by a D.C. valves? Provide one ex with diagram.

problem 3) What do you mean by a Stepper Motor? describe in detail.

problem 4) What do you mean by Ladder Logic diagram in PLC?

problem 5) What do you mean by Cushion Assembly in valves?

problem 6) What are Robot End-effectors? Provide one ex?

problem 7) What do you mean by Robotics?

problem 8) prepare down the difference between Hydraulic and Pneumatic valves?

problem 9) What do you understand by Low Cost Automation?

problem 10) What do you understand by Data Acquisition?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98958

Have any Question? 


Related Questions in Mechanical Engineering

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

Salt water containing 192 lbgal of salt flows at a fixed

Salt water containing 1.92 lb/gal of salt flows at a fixed rate of 2 gal/min into a 100-gal tank, initially filled with fresh water. The density of the incoming solution is 71.8 lb/ft 3 . The solution, kept uniform by st ...

There are 3 x 103 spheres in a box calculate the number of

There are 3 x 10 3 spheres in a box. Calculate the number of different combinations for the spheres in order to have 1100 spheres in the front third of the box. Assuming that the distribution is normal, calculate the pro ...

Use eqn 135 to find expressions for the rate of change of

Use eqn 1.35 to find expressions for the rate of change of the expectation values of position and momentum of a harmonic oscillator; solve the pair of differential equations, and show that the expectation values change i ...

The following table gives averaged total energies for a

the following table gives averaged total energies for a series of Monte Carlo Ising model simulations at different temperatures. Calculate the approximate heat capacity of the system before and after the phase transition ...

Equipment engineering and design structural failure

Equipment Engineering and Design Structural Failure Problem- Background - A 6 ton pressure vessel - see dimensioned drawing - was being lowered onto a "stillage"or temporary supporting structure for testing outside a fac ...

Hydraulic circuit pressure dropthe hydraulic circuit shown

Hydraulic Circuit Pressure Drop The hydraulic circuit shown involves a pump and four pressure restrictions. Assuming the reservoir is at atmospheric pressure and the flow is at steady-state, determine the gage pressures ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

There is a typo in the problem related to combustion of

There is a typo in the problem related to combustion of hydrazine. The sentence alluded to products should read: "Because of the fuel choice, expected products of combustion are H2, N2 and H2O"In the version you received ...

1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro