Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) prepare down the disadvantages of air refrigeration system?

problem 2) What do you mean by isentropic efficiency of compression and expansion? describe in detail

problem 3) prepare down the effect of Superheating on performance of vapour compression refrigeration system?

problem 4) What do you mean by flash chamber?

problem 5) prepare down the principle of vapour absorption refrigeration system?

problem 6) From the environment consideration ammonia is taken as a better refrigerant, but still it is not used in domestic refrigerator. describe why in detail.

problem 7) How air conditioning, differ from refrigeration?

problem 8) What do you mean by effective temperature?

problem 9) What is wet bulb depression? Provide its importance.

problem 10) How will you describe desert condition of air?

problem 11) State humidity ratio, Dew point temperature, apparatus dew point Temperature and humid specific heat. What are the major factors affecting performance of simple vapour compression refrigeration system?

problem 12) describe three fluid system of refrigeration with well labelled sketch giving the function of each fluid in the system.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98940

Have any Question? 


Related Questions in Mechanical Engineering

The space between two very long parallel plates separated

The space between two very long parallel plates separated by a distance h is filled with a fluid with viscosity where μ0 is a constant and n is a constant exponent. The top plate slides to the right with a constant speed ...

We want to tighten an astm a193 bolt having 4-8 un threads

We want to tighten an ASTM A193 bolt having 4-8 UN threads and a yield strength of 96 ksi. The effective length of its body, Lbe, is 12 in.; that of its threads, Lse, is 4 in. We're going to control the buildup of preloa ...

The viscosity of heavy liquids such as oils is frequently

The viscosity of heavy liquids, such as oils, is frequently measured with a device that consists of a rotating cylinder inside a large cylinder. The annular region between these cylinders is filled with liquid and the to ...

The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

One excited state of the sodium atom lies at 25 73986 cm1

One excited state of the sodium atom lies at 25 739.86 cm1 above the ground state, another lies at 50 266.88 cm-1 . Suppose they are connected by a perturbation equivalent in energy to (a) 100 cm -1 , (b) 1000 cm -1 , (c ...

Linear motion actuator with feedback controlanalyses and

Linear Motion Actuator with Feedback Control Analyses and Simulations Provide complete mathematical modeling of the system and its components (free body diagrams and differential equations are required). Provide a comple ...

1 the circular gate abc has a 1 m radius and is hinged at b

1. The circular gate ABC has a 1 m radius and is hinged at B. Neglecting atmospheric pressure, determine the force P just sufficient to keep the gate from opening when h = 12 m. 2. The figure below shows an open triangul ...

A prototype bolt shaft assume a uniform cylinder that is to

A prototype bolt shaft (assume a uniform cylinder) that is to be loaded in tension is made of a stainless steel with a yield strength of 450 MPa and has a safety factor of 3 with respect to yielding for the maximum allow ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

1 the pump shown in the figure delivers water at 59degf at

1. The pump shown in the figure delivers water at 59°F at a rate of 550 gal/min. The inlet pipe has an inside diameter of 5.95 in. and it is 10 ft long. The inlet pipe is submerged 6 ft into the water and is vertical. Es ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen