Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. prepare down the advantages and disadvantages of geo – thermal power plant.

2. What are the advantages of tidal power plants over hydel power plant?

3. prepare down the advantages and disadvantages of OTEC power plant.

4. prepare down the principle of OTEC?

5. prepare down the components of tidal power plant?

6. What do you mean by Heliostats?

7. describe the importance of incremental rate of a power plant?

8. prepare down the different operating cost of coal fired steam power plant.

9. What do you mean by “Diversity factor”?

10. What do you mean by fixed cost and operating cost?

11. prepare down the importance of two part tariff and three part tariff?

12. prepare down the main factors which decide the economics of power plants?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911720

Have any Question? 


Related Questions in Mechanical Engineering

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

A small three-phase ig has the following nameplate data 110

A small three-phase IG has the following nameplate data: 110 V, 1.140 rpm, 60 Hz, Y connection, and 1250 W. The blocked rotor test at 60 Hz yielded the following: I = 69.4 A, P = 4200 W. The turn ratio between stator and ...

This atomic force microscope probe is a silicon beam and

This atomic force microscope probe is a silicon beam and tip. The beam is 40 µm wide, 4 µm thick, and 130 µm long. The tip is set back 15 µm from the end of the cantilever. The deflection of the tip is 1 µm for every 42 ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

Consider the torsion of a thin-walled tube determine an

Consider the torsion of a thin-walled tube. Determine an approximate expression for the torque if the shear stress must be less than a given working stress τw. Express this result in terms of the tube's mean radius R and ...

An air conditioner is a refrigerator with the inside of the

An air conditioner is a refrigerator with the inside of the house acting as the cold reservoir and the outside atmosphere acting as the hot reservoir. Assume that an air conditioner consumes 1.70 X 10 3 W of electrical p ...

You need a reort if 10 pages and above the report about

You need a reort if 10 pages and above. the report about colorimeter specificly measuring spesific heat. anything you need will be provided. format sample has been will be provided. and a report sapmle will be provided t ...

Derive a formula for the minimum energy in the

Derive a formula for the minimum energy in the two-dimensional Using model, if the interaction energy between each spin and each of its eight nearest neighbors is -D. Assume that the model consists of a rectangular array ...

The lateral base resistance is a fundamental limitation of

The lateral base resistance is a fundamental limitation of high-frequency and high speed performance of BJTs. At low temperatures, deionization of the dopant impurity could increase the base resistance much more than the ...

An electrical motor is used to operate a carnot

An electrical motor is used to operate a Carnot refrigerator with an interior temperature of 0.00°C. Liquid water at 0.00°C is placed into the refrigerator and transformed to ice at 0.00°C. If the room temperature is 300 ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro