Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) prepare down the kinds of biasing a PN junction. describe them in detail.

2) What do you mean by forward bias and reverse bias in a PN junction?

3) What do you mean by reverse recovery time?

4) What do you mean by break down? prepare down its types?

5) What do you mean by Zener breakdown?

6) What do you mean by avalanche break down?

7) Describe why transistor is called a current controlled device?

8) describe when transistor acts as a switch in detail.

9) What do you mean by a biasing? describe in detail.

10) What do you mean by operating point?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911921

Have any Question? 


Related Questions in Electrical & Electronics

1 discuss the evolution of the half-wave dipole from an

1. Discuss the evolution of the half-wave dipole from an open-circuited transmission line. 2. Justify the approximations involved in evaluating the integrals in the determination of the radiation fields due to the half-w ...

1 discuss with the aid of an example the discharging of an

1. Discuss with the aid of an example the discharging of an initially charged line into a resistor. 2. Discuss the bounce-diagram technique of transient analysis of a line with uniform initial voltage and current distrib ...

Consider the complementary-bjt class b output stage and

Consider the complementary-BJT class B output stage and neglect the effects of finite VBE and VCEsat. For ±10-V power supplies and an 8 ohm load resistance, what is the maximum sine-wave output power available? What supp ...

1 find the unit vector normal to the plane then find the

1. Find the unit vector normal to the plane . Then find the distance from the origin to the plane. 2. Write the expression for the differential length vector dl at the point (1, 2, 8) on the straight line and having the ...

A certain communication channel has a bandwidth of 10 khz a

A certain communication channel has a bandwidth of 10 kHz. A pulse of 0.5 ms duration is transmitted over this channel. a. Determine the width (duration) of the received pulse. b. Find the maximum rate at which these pul ...

1 two immiscible fluids of different density and viscosity

1. Two immiscible fluids of different density and viscosity are flowing between two parallel plates. Express the boundary conditions at the interface between the two fluids. 2. Determine the velocity profile for fluid fl ...

A a signal x t 5 sinc2 5pit cos 20pit is sampled at a

a. A signal x (t) = 5 sinc 2 (5πt) + cos 20πt is sampled at a rate of 10 Hz. Find the spectrum of the sampled signal. Can x (t) be reconstructed by lowpass filtering the sampled signal? b. Repeat part (a) for a sampling ...

1 in jpeg explain why we need to round the result of

1. In JPEG, explain why we need to round the result of division in the quantization step. 2. Explain why the combination of quantization/dequantization steps in JPEG is a lossy process even though we divide each element ...

1 if alice and bob need to communicate using asymmetric-key

1. If Alice and Bob need to communicate using asymmetric-key cryptography, how many keys do they need? Who needs to create these keys? 2. Why do you think asymmetric-key cryptography is used only with small messages. 3. ...

1 a rectangular block of concrete 3 ft times 3ft times 6 in

1. A rectangular block of concrete 3 ft × 3ft × 6 in. has its 6- in. side half buried at the bottom of a lake 23 ft deep. What force is required to lift the block free of the bottom? What force is required to maintain th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen